PDA

View Full Version : Replacing Fuel Injector(s)



Spindrift
06-02-2012, 01:02 PM
I have had my van for about a week. I was smelling fuel so I called the previous owner and he says; "You didn't fill it up did you?" I said "Yes, remember it was below empty when I got it?" He was trying to tell me you never fill a van because the tank runs length wise. - Whatever, I realized I was on my own. Lifted the cover and noticed gas coming from the 2nd injector. Took a picture and sent it to our family mechanic and he says "At least 600.00 to fix." So here I am. I only paid 900.00 and expected I would be dealing with some of this. I have rebuilt motorcycles but id say the most I have ever done to a car was replace a thermostat. This is a little scary. After seeing some of Tim's posts and seeing various parts disassembled though I feel a little empowered so I began taking stuff apart. I think I have almost every hose off except for the banjo fitting on this (what I believe is a pressure regulator).

My first Question:
This thing looks like it is a booger to get off and it scares me a little. It looks like the banjo part is part of the nut. My question is... Is that banjo part connected to the nut part? If so how in the world do you get it off? Is there anything I need to be careful about?

Question 2:
I told my mechanic about "Dr. Injector" that is supposed to be a whiz in the Portland area for fixing injectors. My mechanic says "Don't do it. Get new or you will be sorry." I am all for saving money but not if I have to do this again. I would love to get some advice on this matter. If others have used "Dr. Injector" I would love to hear more. If you have bought new injectors which do you recommend? I am clueless here and more than a little nervous. I see injectors listed from 35.00 to 235.00 and I am not sure what is what.

On a side note. People complain about engine access on these and what a roflroflroflroflrofl it is to work on them but I have found a lot of bonuses to this. For one I am not breaking my back leaning into the engine compartment. I have a nice little seat (out of the rain... a bonus for Portland) and you hardly have to reach for anything. Getting to the back goodies is a bummer but I cut a couple of access holes after studying the "Hose of Death" thread and now that part is easy too. All and all I like it. Even with the trouble I have already I am in love with this thing. I really want to figure this thing out because I see it as a perfect vehicle for me. Hopefully after this chapter we will have many happy times together.

Any and all help much appreciated.

BTW
I also included a photo before I cut some holes. I modified them a little but basically the black square on the right is from the "Hose of Death" (http://www.toyotavantech.com/forum/showthread.php?213-The-hose-of-death-thread) thread (thanks Tim) and the pink highlighter is my own creation to get to some of the bits I could not reach. Tim must have arms like Houdini. I would have driven myself mad trying to get these bits on the left. I will show the final hack in another post. I used a Dremel and about 7 blades to do this so I would recommend using the little saws all Tim had if you have one.

timsrv
06-02-2012, 02:35 PM
Hi and welcome to TVT! That fuel component in your 1st picture is the pulsation damper. It is incorporated into the bolt that passes through the banjo fitting. To get it off use a 22mm or a 7/8" wrench (it's okay to interchange standard tools on some of the bigger fasteners). To help you get a better grasp on how it fastens, here's a picture of one that's not installed:

http://i8.photobucket.com/albums/a23/timsrv/TVT%20pics/Fuel%20system/IMG_2200.jpg

These have a tendency to develop leaks and start fires, so if you're removing it and don't know the history I would recommend replacing it. It's Toyota part #23270-50011. If you want genuine Toyota (recommended) it's current MSRP is $94.70 but it can be had for ~$70 if you purchase from one of those discount Toyota parts sites like www.toyotapartsdeal.com. I'm currently running a Standard Motor Products (SMP) part #FPD4 (http://www.rockauto.com/catalog/moreinfo.php?pk=1002665) damper that I purchased from www.rockauto.com for $37.79 and so far it's been solid.

Toyota's injectors rarely fail, but these vans are getting old so we're beginning to see issues here. My personal opinion is a good used Toyota injector is probably just as good as (perhaps better than) a rebuilt injector from who knows where, so if you're injectors test good then I'd keep using them. I would however strongly recommend having them cleaned and tested before putting them back into service. I'm assuming you saw my recent post about Dr. Injector in Gladstone, but for anybody else that might be interested here's a link: https://www.toyotavantech.com/forum/showthread.php?522-Other-parts-to-replace-while-replacing-Head-Gasket (scroll down to post #15). Tim

timsrv
06-02-2012, 02:40 PM
Here's another thread that may help you with your fuel system issues: http://www.toyotavantech.com/forum/showthread.php?589-Testing-fuel-system-replacing-fuel-pressure-regulator

Spindrift
06-02-2012, 02:50 PM
Thanks Tim! That is probably a good call. Could a bad pulsation dampener cause the injector blowout/failure? Something is seriously blown in that #2 because gas is pouring out big time. I worry is that old plastic might pass the test but fail later (like #2 did) just because it is old plastic.

I guess I will probably go check out the Dr. and get his opinion on the old plastic.

Question1:
It looks like my hose(s) of death have been replaced but I still need to remove them to get the manifold off and the fuel rail right?

Question 2:
Will the injectors just pop out when I get the manifold/fuel rail off?

timsrv
06-02-2012, 03:16 PM
Wayne at Dr. Injector knows his stuff. If he says you can run the injector then you can run it. If it's bad or marginal he'll tell you. Pulling the top half of the manifold is somewhat of a PITA. Yes, you will want to pull the hose of death to separate. You will also need to pull the EGR valve and modulator off. The cold start injector tube will need to be removed as well. There are some other hoses/tubes & associated fasteners that will need to be removed too. After you get the obvious stuff, lift, wiggle, and probe for the rest. Once the top half is removed you will want to remove the fuel return line from the FPR (Fuel Pressure Regulator) and remove the injector connectors. After that there's just 2 bolts that hold the fuel rail on. Remove those and the fuel rail will pull right off. The only thing holding the injectors in place is their o-rings between the manifold and the fuel rail. They will either pull off with the fuel rail or stay in the manifold. Either way it's just a tug and a twist to finish removing them (after the rail has been removed).

One thing to watch out for is old seal material or debris left in the injector mount holes. If you install injectors with debris in there you will likely create a leak and/or damage the rail and/or the injectors. Just make sure everything is clean and use a small amount of petroleum based grease to pre-lube the isolators/o-rings before assembly. Tim

timsrv
06-02-2012, 03:20 PM
The only thing the pulsation damper does is smooth out the pulsations created by the fuel pump. There's basically just a diaphragm with a spring in there. From the perspective of dampening pulsations, they never fail. Failure occurs when the diaphragm tears and fuel starts leaking all over your hot exhaust manifold :shock:.

llamavan
06-02-2012, 05:31 PM
My first Question:
This thing looks like it is a booger to get off and it scares me a little. It looks like the banjo part is part of the nut. My question is... Is that banjo part connected to the nut part? If so how in the world do you get it off? Is there anything I need to be careful about?

HERE (http://www.toyotavantech.com/forum/showthread.php?231-Replacing-your-fuel-pulsation-damper) is the tutorial for replacing the fuel pulsation damper only.

Gwen

Spindrift
06-02-2012, 05:45 PM
You have me sold on the good doctor Tim. I know I will catch hell from my girlfriends mechanic (who is a friend also) but the Dr sounds way cheaper and I trust you both have much more experience with this. I hope to have the manifold off today or tomorrow. I think I will try to clean everything up as well as I can so I can become more familiar with it and to better trace leaks and such later. I also want to replace all of the rubber. I think I will even replace the replaced "Hose of Death" just to have it all fresh. Rubber is cheap and I am here.

Maybe I will replace the valve cover gasket too. Does that need to be OEM also?

I will be taking the injectors to the doctor Monday and see how long it takes. Can't wait to get this back together. I was just about to start building a bench/bed when I launched into this. Looking forward to smelling like wood instead of gas.

Do I just take the injectors only to the doctor?

Spindrift
06-02-2012, 05:53 PM
Thanks for the tutorial Gwen!

timsrv
06-03-2012, 01:18 AM
Maybe I will replace the valve cover gasket too. Does that need to be OEM also?

I will be taking the injectors to the doctor Monday and see how long it takes. Can't wait to get this back together. I was just about to start building a bench/bed when I launched into this. Looking forward to smelling like wood instead of gas.

Do I just take the injectors only to the doctor?

I typically buy enough parts through Toyota that I get the VC gaskets there too (more for convenience reasons than anything). Rockauto.com was having a close-out on the Beck Arnley VC gaskets a few months ago for $.80 each so I got a dozen of them. I installed the 1st one a couple months ago & didn't see anything wrong with it. It fit nice and it sealed up fine. I probably won't buy anymore Toyota VC gaskets until I use these ones up...........unless a problem arises, but I sort of doubt that will happen.

Just take Wayne the injectors. If you have suspicions about any of your other fuel system parts you may want to bring them along just in case. I know he offers other services there and may be able to help with other issues. It will only take him 1/2 hr or less to do all 4 injectors. Assuming he's not tied up with anything else he'll likely take you back to watch the process. If there's a problem he'll point it out so you can see for yourself. If you need another injector I'm guessing he'll have it for a reasonable price. He's got bins & bins of injectors and repair parts at his fingertips. I feel like a kid in a candy store when I go there :)>:. Tim

Spindrift
06-03-2012, 11:36 AM
Thanks Tim! I usually don't like to go to the doctor I am really looking forward to this visit!


:clap:


Can't wait to get the old girl on the road again!






:silvervan:

Spindrift
06-04-2012, 02:48 AM
I finally got my manifold off today (!) and have been looking over the rubber. I am assuming that the hoses with factory clamps is probably original equipment. Both of the "Hoses of Death" look like they were replaced but if this is cheap I might as well put fresh rubber on. This looks like pretty standard get anywhere hose right?

Here is a look underside the manifold where things seem a little crunchier.

I should have asked this before. Is there an online microfiche type thing where I can identify parts and get part numbers? I have a lot more questions now. What is this stuff?

(1) Do I need to replace this gasket?

(2, 3, 4) These are pretty hard. Should I replace and if so can I get this hose anywhere?

(5) This hose cracked it was so brittle. I think I have seen this hose at the parts store. I have extra gas line hose but it says "Do not use for fuel injection" or something like that. I guess that is a pressure thing? This cracked hose will appear in the next two shots also.

(6) This hose is brittle. If it is not a high pressure or super critical maybe I can let it slide? It looks like it must be from Toyota with all the fancy manufactured bends. Right? Probably spendy.




:thmbup:






http://www.toyotavantech.com/forum/attachment.php?attachmentid=674&d=1338793815

This next picture is just to remind me to get lots of these little brass washers.

(1) Do I need a special part number or can I just take them into the auto parts store and get the same size?

(2) How hard do I torque the little brass washers?

note: there's that cracked hose again


:wave1:


http://www.toyotavantech.com/forum/attachment.php?attachmentid=675&d=1338793831

And finally here is my pressure damper. Looks ancient. I guess originally it had a screw in that little hole from what I read in another thread. I am going to hold off ordering this and see if maybe the doctor knows where to get one tomorrow.

(and there is mr. cracked hose again

:wave2:

)

http://www.toyotavantech.com/forum/attachment.php?attachmentid=676&d=1338793843

timsrv
06-04-2012, 03:52 AM
Nice job! This thread should help: http://www.toyotavantech.com/forum/showthread.php?342-Top-End-Rebuild&p=2052#post2052

Spindrift
06-04-2012, 11:32 AM
Thanks Tim! So I gather you WOULD replace ALL of the rubber. Correct?

timsrv
06-04-2012, 01:08 PM
Yes..........unless you feel like splitting the manifold again in 2 or 3 years to replace just one or 2 of them :lol:. Assuming that's original rubber I'd say now is a good time. Tim

Spindrift
06-04-2012, 01:18 PM
Yeah. Not so much. I will take your advice. Almost ready to go to the Dr. Keep you posted.

Spindrift
06-05-2012, 07:25 PM
Where do I find the part # for the intake gasket?

Also the little brass washers that go with the banjo joints... I can get those anywhere right? I ordered the BIG ones for the pulsation damper because I had the #'s and I thought they might be slightly harder to find.

PS. Dr. Injector says my injectors had horrible spray patterns, two leaked and all had low flow. He has my injectors rebuilt and hopefully I will be getting all of my new on-line rubber before the weekend.

Thank you ALL for the help!

Spindrift
06-05-2012, 07:28 PM
... or whatever the name of this gasket is.

http://www.toyotavantech.com/forum/attachment.php?attachmentid=674&d=1338793815

timsrv
06-05-2012, 07:50 PM
That gasket is not interchangeable from 3y to 4y, so in your case (3y) you'll want Toyota part #17176-73010. I'm sure it's also available aftermarket. If you go that route be sure to specify it's a 3y. It's called a "surge tank gasket". The little copper washers are Toyota part #90430-08005. If you like the ones with the little tab sticking out those are part #90430-08007. These are common parts so I suspect if you walked into any auto parts store and showed them one they could easily match them up. Tim

Spindrift
06-05-2012, 08:20 PM
Thanks Tim! What does 3Y 4Y mean? I keep seeing that and you'd think I would have figured it out by now. I originally thought these were the same engines used in the trucks from the same time but I hear this is a entirely different creature yes? Like some sort of forklift engine. Can you point me to more info on this?

timsrv
06-05-2012, 08:44 PM
The 3y is a 2.0 liter and was only used in 84-85 vans. The 4y is a 2.2 liter and was used in 86-89 vans. The 4y is also used in forklifts. These are the only applications for these engines in the US market, but foreign markets may have used them in other vehicles. Tim

Spindrift
06-15-2012, 10:05 AM
I got the first batch of hoses in and started putting them on my manifold. The Toyota hoses go on in a snap as someone said but the first bulk hose I have tried is a real bugger. I took in a piece of hose to the auto parts store and this is what they sold me. Could someone take a look at the photos and tell me if I am trying to put the wrong hose on here.

It was the closest size they had and the guy said it was what I wanted. It says "multi fuel compatible" does that mean it is OK. I have some hose here from a motorcycle project that says "not for fuel injection." I am wondering if I need some kind of special line or something?

The photos show the hose, where it goes, (by the way the piece looks long because I have not trimmed it yet), a comparison of old and new where you can see the hole size. I realize the bulk hose is harder to get on but this was almost ridiculous. The shot where the hose is finally on took some lube (rubber conditioner... Meguires) and about 20 minutes of sweat and it still isn't on there good. Am I just a weakling?

687688689690691

timsrv
06-15-2012, 11:20 AM
If the hose doesn't fit easily then I'd look for a different piece of hose. You may have to go to another parts store to find it. The one in your picture doesn't need to be rated for fuel injection as it's just a vacuum line. Tim

Spindrift
06-15-2012, 12:09 PM
Thanks Tim. That was what I was wondering but it seemed to big to be just a vacuum. I will check another store.

Spindrift
06-17-2012, 08:24 PM
I thought today I was going be riding into the sunset on this project but not so much. I think I have everything back right. Almost. It seems I have an extra part. Maybe someone can draw a line to where it goes in this picture.
http://www.toyotavantech.com/forum/attachment.php?attachmentid=692&d=1339982183


I was a little apprehensive to try to start it because I couldn't remember where this part went and also because I was the mechanic but I tried and it runs!!! :rol: I only ran it for a few seconds but it seemed to purrrrrr for those seconds.

The thing that kept me from driving it thought was this. As I was putting the coolant in I heard a trickle and found this. I remembered when I put the hose on the radiator felt a little soft. Am I looking at a new radiator or can I get this repaired successfully? :pissed: Shoot!

http://www.toyotavantech.com/forum/attachment.php?attachmentid=693&d=1339982209

timsrv
06-17-2012, 11:21 PM
That little piece is a support bracket. It goes between the upper and lower intake manifolds and also provides a mount for the cold start injector line. It would probably be okay without it but there's a small chance of stressing something due to vibrations (over time) if it's not there. You are lucky it's the front bracket and not the rear one. It should be easy to put on..........Here's a picture showing the correct location.

http://i8.photobucket.com/albums/a23/timsrv/TVT%20pics/Engine/IMG_2340.jpg

That's a bummer about the radiator. Looks like it will need to come back out again. Just take the radiator and the broken nipple down to a radiator shop and they should be able to repair that for you. I'd probably have them remove a tank and inspect/rod it out while it's there. I'm guessing the repair, inspection, rodding out, will cost around $100 - $150. I'd ask them to beef it up a bit in this area so it doesn't happen again. Tim

Spindrift
06-18-2012, 10:10 AM
Perfect! Now my memory is coming back. Glad it is in the front!

Can't I get a new radiator for about that cost? The volvo radiator I bought about a year ago was only 150.00 new. Do they re-manufacture these in plastic?

I am sure I can figure it out but do you know of a good thread that covers radiator removal?

Thanks Tim. It is so helpful to be able to ask an expert. I will be donating again very shortly. I would be lost without this site.

timsrv
06-18-2012, 01:53 PM
Can't I get a new radiator for about that cost? The volvo radiator I bought about a year ago was only 150.00 new. Do they re-manufacture these in plastic?


I've never purchased a new 3y radiator, but from what I've heard the only ones available new are junk. I think Gwen (llamavan) has been down this road so perhaps she'll chime in here with a solution and/or place to buy. Personally I let the radiator specialists tell me what to do. If they say replace then I purchase from them. Since cooling is so important, I always ask if there's any upgrades available. Sometimes they can add another row of cooling core and/or install a higher efficiency unit. Depending on what they can do it could cost as much as $450 (for the works) but I'd consider it money well spent. If you're on a shoestring budget, then go with repair (or the minimum they recommend). Tim

llamavan
06-18-2012, 06:32 PM
Toyota rads for the 3Y vans are NLA. :cry:

There are plastic-tanked aftermarket rads still available, but I wouldn't put one in MY van if you paid me. :no:

CSF aka Cooling Systems and Flex (which has metal tanks) has apparently quit making the 3Y rads also, but I could be wrong (and hope I am). But ... all the retail internet sources that I found fessed up that they don't really have any after I tried to buy one. :?:

I did recently score a NOS CSF rad for a 3Y van on eBay after looking a very, very long time. But that doesn't help you (other than clarifying that finding one is probably not a "next day" or "next week" kind of thing).

Gwen

Spindrift
06-19-2012, 01:09 PM
Thanks for the feedback. I just removed the radiator and it feels so frail! the top strip of metal came off one side and one 1/4 row of those little squiggely things is lifting off the same side. It doesn't look good to me. I will take it to the radiator shop and see what happens.

In the meantime. I found a couple of the last hoses I have the parts for but had not found. There is a whole other world to explore in front of the radiator huh? What are those other two radiator type things? Do I need those? Oil coolers or something? I thought maybe of one was associated with the air conditioning maybe I would get better air flow without it?

Anyway I am off to the radiator shop.

timsrv
06-19-2012, 01:27 PM
Your front heater core is mounted right above the floor boards in the very front of the van. There are 2 heater hoses (one with an in-line valve) that go to it. Everything else up there is either power steering or air conditioning. There's also one vacuum line that goes to the brake booster in the very front. Tim

Spindrift
06-23-2012, 04:03 PM
I got my radiator back from the shop. It turned out it was pretty bad so I ended up replacing the core. The new core + the maintenance ran me 245.00. Here is a shot of it posing next to my freshly painted wheels.

http://www.toyotavantech.com/forum/attachment.php?attachmentid=697&d=1340485345

After I got the radiator in and put in the fluids I started it up. It fires right up and then seems to struggle. It sounded way better before I stated this project. I must have a vacuum hose out of place or worse. At least it doesn't smell like it is ready to go up in flames. I probably jumped the gun putting the seats back in. I am guessing I probably should have adjusted the timing and at least checked the plugs.

One thing that kind of worries me is that I got the #1 and #3 injector wires crossed (the first two you can see). I never marked the wires (!!) and I think I assumed the wire that best reached would be the right one but I think there is a chance I did this. Would the engine run at all if I did? I can still get to those first two connections if someone thinks that is a possibility.

The other things that are circled are confusing me also could someone tell me what these round things do? I don't think I have the hoses right do I?

The bigger of the two has a hose from the bottom that is short and connects directly below it correct? I couldn't find a diagram to help me here.

http://www.toyotavantech.com/forum/attachment.php?attachmentid=699&d=1340486353

Here is a closer photo.

http://www.toyotavantech.com/forum/attachment.php?attachmentid=700&d=1340486660

Could I have damaged the smaller plastic one by cleaning it. Speaking of the alternator and/or some of the bits by the fan in the front of the engine seem nosier since I did this work. Could it be because I cleaned it (SuperClean)? Maybe all the grease was good for it.

And here is a short clip of me starting the engine. My iPhone does not do the best with sound but here goes. By the way I just hooked up the accelerator which is why I pushed on that to rev the engine. Can anyone tell by sound what might be wonked up?


http://www.youtube.com/watch?v=1xJsXe0OwEw&feature=g-upl

Spindrift
06-23-2012, 11:12 PM
Just a quick update. I started it up a couple of times today to take notes. It is pretty consistent when it is cool. It starts right up and sounds good (to me) then about 6 seconds into it it starts struggling and if I don't give it gas it will die. Sound familiar? Also, I don't know if it is me but it seemed to run a little better today than it did in the video. Seems like it maybe is smoothing out. The exaust didn't seem as inconsitant. When I first started the new pastic and the special grease Dr. Injector gave me smoked and gave an aweful smell but it doesn't do it now. Could it be that the fuel lines just have air and that some of that initial plastic burn off was making it run rough? It really does seem to be a little better.

If anyone knows of a couple of vacumme hoses I could have gotten confused please chime in. :wall:

timsrv
06-24-2012, 01:14 AM
I could see maybe getting the wires for injectors 1 & 2 reversed, but it would be pretty hard to get any of the others mixed up. I can't imagine getting 1 & 3 mixed up. The length of wires on the harness would make that very difficult.

Those 2 round things in the back of the engine are your EGR valve & EGR modulator. From what I can see in the picture they look to be hooked up correctly. The modulator (plastic one) also has a hose on the bottom (can't see it in the picture). Make sure that one is hooked up.

I can't tell much from the video, but it sounds to me like a power steering noise. Did it do that before? Could be a cavitation noise due to low fluid??? You should have a vacuum line diagram sticker on the driver's side edge of the engine bay. If not I could probably conger one up for you. Tim

kcg795
06-24-2012, 04:23 PM
I usually hear that sound when I have my steering cranked all the way, but not quite as loud. Too bad we couldn't convert to Electric Power Steering. My Cobalt has it and I love it. Don't have to worry about fluid leaking. Other than that noise, the engine sounds like it's running ok. I don't think a 23-28 year old engine is ever going to run perfect. The 10% ethanol in the gas is pushing it because the manual basically says to use it only if you have to, and we don't have a choice now.

Spindrift
06-24-2012, 04:56 PM
You have a good ear Tim. I was still adding fluids but I checked my power steering and it was way low.

So I took a quick spin down the block and have a new laundry list of issues. Biggest one "Where are my brakes!?!" Good thing it wasn't running great or I would be in trouble. I crawled back and was trying to find the brake fluid reservoir when I found a pretty major vacuum line off... one of the big ones that go into the valve cover (Duh!) it was hidden. While I was over there I checked the plug connections and one clicked -wasn't all the way on. It purrs like a kitty. I think I can put the injector thread to bed! :clap::clap::clap:

Now for the brakes WTF? What should I check first? I am under the gun now. To save face on this van purchase with my life partner I have to have it ready to explore Eastern Oregon by the weekend! The brakes didn't seem great but they were horrible on my little one block trip. I must have messed something up.

Was looking for a how to on brakes here but not really finding it. If someone knows of some good posts let me know.

timsrv
06-24-2012, 06:09 PM
Make sure this hose is hooked up correctly. This is the vacuum supply line for your power brakes. It should go from the metal tube on the firewall to the intake manifold. Tim

http://i8.photobucket.com/albums/a23/timsrv/TVT%20pics/Brakes/IMG_2357.jpg

Spindrift
06-24-2012, 06:43 PM
That's the hose! The one I found off. Maybe now my brakes work!?! I guess it was the spark plug wire that wasn't all the way on that was making it run rough.

By the way the engine purrs now!!!! Confirmed. And with the proper level ATF the noise has been reduced.

By the way the big long hose that goes to the power steering is about the only hose I have not replaced. It is hard as a rock and oozing a bit where it connects. I bet it is expensive with all those turns and added foam. Do you happen to have the part # for that?

I am going to go see if the brakes work now. I will report back shortly.

timsrv
06-24-2012, 09:10 PM
Awesome! If the power steering is still making noise, you might want to take a look at this thread: http://www.toyotavantech.com/forum/showthread.php?214-Power-steering-system-noise . That power steering hose is still available but the dealer will want around $140.00 for it. The discount sites like www.1stToyotaParts.com will want around $100.00. It's Toyota part #44348-28040. Some people get the bulk 5/8" I.D. hydraulic hose and use that, but I prefer the molded Toyota hose. It's hard to justify the cost but the fit is much better. Tim

Spindrift
06-25-2012, 03:21 PM
I have a great running van with working brakes no less!:silvervan: Thank you to everyone that helped. I don't know how I would have done it without this site and everyone's patience. I know I wouldn't have had the guts to go in in the first place if I wouldn't have found this site.

So the take away on this is.

1) If the most you have ever done to a car is change oil or a thermostat this is doable provided you have this site and some patience. Take lots of pictures!
2) You can save a ton of money rebuilding injectors vs buying new. I was skeptical at first because my mechanic told me not to do it but after seeing the process it seems ridiculous not to have your original ones rebuilt unless you just like spending money. All of the non metal bits get replaced into the sonically clean shaft and 25.00 is cheaper than 225.00.
3) Fix ALL of the rubber while you are in there. Some of those hoses "look" fine but if they are from the 80' chances are they will crumble when you try to remove them and if you don't do it now they will crumble on their own - at the most inopportune time.
4) After installation go through and check all of the hoses and lines again. When you are done do it again. Be sure the hose in the last photo that Tim posted is connected or you might drive through the neighbors house.

:wave2:

JFratzke
06-25-2012, 11:58 PM
Great job getting your van running!!! Superb pictures and write-ups too with excellent Tim AND llamavan advice! I have a 4Y but I still feel like I learned plenty from the read. Spindrift--here is where I can help: I am an Eastern Oregon native and as a fellow Toyotavan owner, feel free to ask me anything about the area. And I hope you are not talking about Bend cause that's central Oregon to us out here. I have recently gotten my 1987 4x4 Cargo Conversion up and rolling all around the hills. This last weekend my son and I drove the Hells Canyon Loop road from Halfway to Joseph and it was awesome! If you have any questions about must-sees, dining tips, camping advice, or just about anything else, feel free to message me. Our vans were built for the adventures Eastern Oregon provides!

Spindrift
06-26-2012, 10:35 AM
Thank you! Yes and thank you to Tim and Llamavan for the great advice. Hopefully I am going to get this thing licensed today.

Thanks for the offer. Where are you in Eastern Oregon? My girl is actually from Nyssa. She turned me onto the Alvord a couple of years ago when we were coming back from Yosemite. I was resistant at first to go so far out of the way but it changed me... I became obsessed with E Oregon. Got back into motorcycles just so I could ride out there. If it all comes together we will be out there the week of the fourth. Be great to meet you. I would love to check out a 4x4 now that I am a van junkie. That sounds like the ultimate.

We went to hells canyon last year and actually saw that alpha female wolf right beside the road. We argued whether it was a coyote or wolf all the way home then my girl looked it up and there she was... wolf... almost black. We also did Leslie gulch which totally blew my mind. Had no idea we had our own Utah out there. If you live out there you are truly blessed. Hope to run into you one of these days.

Spindrift
06-26-2012, 10:37 AM
Oh I see now... Cove Oregon. I have no idea where that is.

JFratzke
06-26-2012, 11:30 AM
Right on! Glad to see you've already found some of the treasures out here (Hells canyon and the Alvord). Most folks in Portland refer to the Bend area as Eastern Oregon when that couldn't be further from the truth. Heck, Bend is a 5 1/2 hour drive from here! I live in Cove, about 15 minutes from La Grande, nestled up against the foothills of the Eagle Cap Mountains. There is so much country out here to explore! And the crowds haven't found it yet, which is the best part. Adventurous Portlanders are starting to come out here more and more but for the most part, you can find some serious solitude here if that is what you are looking for. If you haven't done it yet, a favorite for me is a trip up to Joseph and Wallowa Lake. Lots to see and do up there and tons of places for van-camping. Message me and let me know what you are wanting to do and I can point you in the right direction. I also work at a reputable auto dealership, which is a great resource to have when you own one of our vans. Stay in touch and happy travels! You're going to love road tripping in the van!!!!

mahleek87
02-16-2013, 09:59 AM
I was right about to do an oil change and then I noticed this gas leak on my van. It looks like its coming from the fuel pulsation dampner because when I touch it underneath etc I get gas on my hand. I also had a puddle of gas just hanging out in the cradle of my exhaust manifold. Im so glad I noticed this as I would never want my van to burn down.

So do I just buy the fuel pulsation dampner? Any gaskets to go with it? Thanks alot.

Heres a picture of what I discovered. Should I just replace this or try tightening it?
843

timsrv
02-16-2013, 11:38 AM
It's sealed to the fuel rail with two copper washers. Unless it's really loose, these are not likely to leak. The pulsation damper has a rubber diaphragm inside & after 20 something years it's not unusual for these to deteriorate and fail. Don't mess around here, these dampers have been responsible for several vans burning up. Don't even drive the van to the parts store. Borrow a car until you can get it replaced. The copper washers should be replaced too. Tim

mahleek87
02-16-2013, 12:44 PM
Will do Tim, Thanks again. I drove my other car to the toyota parts store and ordered both gaskets and the FPD. Parts wont be in until wednesday of next week so my van will sit in my driveway until then.

I truly believe in faith and things of that nature. It was Valentines Day this week a very busy holiday for our family owned Florist. I drove this van into the ground this whole week averaging 100-140 miles a day. Finally on Valentines day I felt as it was running rough, in my head I thought it probably needs new spark plugs which it could possibily use since it has been 50K since I changed them but it was probably due to the weak gas pressure because of this leak. Something told me not to drive it yesterday and to give it a break. I didnt and then today I was going to do an oil change and drive away but noticed this. Glad I didnt drive it yesterday it could have gone. Glad I am not driving it for all of the money invested in it. I recently fixed my differential noise last week.

I even have a friend in this area who cant really speak english. He has a high mileage van and keeps a fire extinguisher in it. He told me one of his friends van's caught on fire one time.

llamavan
02-16-2013, 06:27 PM
Here is the thread on replacing the fuel pulsation damper (http://www.toyotavantech.com/forum/showthread.php?231-Replacing-your-fuel-pulsation-damper).

The "running rough" you describe, and also starting hard, is what I experienced just before discovering that a FPD had started to leak.

Gwen

cpginkpt
05-01-2019, 03:31 PM
Noticed a bit of fraying on injector 1 connector wire - still hanging on and van runs ok, but looking a bit dicey at best.

Wondering if anyone has documented the specific process Tim outlines in this section of this thread (pic below)?

Ideally I would love to clean that whole area up (spray degreaser?) and replace that wire ( and connector?), but may be best to just leave it alone.

timsrv
05-02-2019, 12:15 PM
#1 injector connector is the most exposed and the most likely to fail. The good news is it's also the easiest to replace (no need to split the manifold). #2 is a little more difficult, but still accessible enough (forget about #3 & #4). That #1 connector in your picture looks pretty rough. If that were mine I'd at least replace that one.

Because your van is an 88, The type connector(s) you need are "bottom slot Denso injector connectors". As far as I know these are only available through the aftermarket (somewhat questionable quality). The only other option is to go to a salvage yard and pull from a 90's Suburu (that's what I do). Here's a couple links to aftermarket connectors on eBay:

https://www.ebay.com/i/152543170429?chn=ps

https://www.ebay.com/i/262880271800?chn=ps

Here's a link to a thread that explains the different (similar) types of Denso connectors: https://www.toyotavantech.com/forum/showthread.php?522-Other-parts-to-replace-while-replacing-Head-Gasket

And finally here's a post where I talk about building your own removable injector harness (84 - 87 van): https://www.toyotavantech.com/forum/showthread.php?522-Other-parts-to-replace-while-replacing-Head-Gasket

And for 88/89 van: https://www.toyotavantech.com/forum/showthread.php?1011-Exhaust-repair-dilemmas&p=5828#post5828

Keep in mind if you build a removable harness you'll also need to remove the upper half of the intake manifold (which I would avoid until other more urgent work requires you to do so). Good luck. Tim

cpginkpt
05-02-2019, 01:46 PM
thanks Tim - very thorough!

I think I'll go for just 1 & 2 connectors for now. Leave the injectors in place and just grab those Denso connectors + pigtails you referenced.

So just unclip (pry?) the connectors off and then pigtail the new connector to the old harness, right?

Any tricks to getting the plastic disconnected from the injector or any other plastic bits on the injector itself that I should be careful of since I am guessing the whole unit will be pretty brittle?

Also - is it OK to just spray some degreaser all over the area so I can see what I am doing? With the distributor is on other side I should be safe (?)

timsrv
05-02-2019, 02:43 PM
When you get the new connectors you will see the part you pinch to release them. With that knowledge you should be able to just pinch and pull the old ones off. The eBay ones I referenced come with short pigtails of wire. Cut the old wire back a bit from the old connector, strip and attach the new connector. You could use standard butt connectors, but due to the critical nature of these, I highly recommend soldering then protecting with shrink tubing.

Yes, you should be able to spray with an engine degreaser and or other such chemicals. If you use carb cleaner or something harsh, it can damage paint and maybe some plastic parts. I would also check the product for flammable warnings and take appropriate precautions. I personally use Mineral Spirits paint thinner as it cleans well without damaging paint or plastic. After the chemical treatment I use a pressure washer on a low pressure setting to finish the job and flush the flammable thinner off the engine.

After rinsing, if doing the passenger side of the engine, I will usually pull and dry the inside of the distributor & cap with compressed air. A 15 minute drive down the highway after flushing will finish drying the engine and surrounding areas. Tim

PS: My local ACE hardware has mineral spirits in a spray can......haven't been able to find it like that anywhere else (I like using that for the smaller projects). For the bigger cleaning projects I usually purchase by the gallon and spray it with a chemical sprayer tool I have.

cpginkpt
05-02-2019, 03:10 PM
perfect - thanks so much Tim!

Jdelgado
09-22-2019, 02:48 PM
This is a fantastic write up! Unfortunately, I'm having trouble finding a replacement injector for my 89, Any one have a brand/part # I can reference in my search?

Thanks in advance :)

timsrv
09-23-2019, 02:33 PM
This is a fantastic write up! Unfortunately, I'm having trouble finding a replacement injector for my 89, Any one have a brand/part # I can reference in my search?

Thanks in advance :)

88 - 89 vans used Toyota part #23209-73010 which was not terribly common and is now NLA. You may be still be able to find these that are rebuilt and/or you could take your originals in to an injector service to have them cleaned/tested. If all else fails, the Bosch injectors used from 84 - 87 can be interchanged. Everything will fit except the elect harness connections. The Bosch injectors are very common and can be found pretty much anywhere auto parts are sold. Even the elect harness connectors are common and can be easily found. If you go this route, you should spend some extra time to be sure the electrical connections are done well and sealed (solder and shrink tube is recommended).

PS: If you change one to Bosch, I would recommend changing them all.

Jdelgado
09-23-2019, 03:57 PM
88 - 89 vans used Toyota part #23209-73010 which was not terribly common and is now NLA. You may be still be able to find these that are rebuilt and/or you could take your originals in to an injector service to have them cleaned/tested. If all else fails, the Bosch injectors used from 84 - 87 can be interchanged. Everything will fit except the elect harness connections. The Bosch injectors are very common and can be found pretty much anywhere auto parts are sold. Even the elect harness connectors are common and can be easily found. If you go this route, you should spend some extra time to be sure the electrical connections are done well and sealed (solder and shrink tube is recommended).

PS: If you change one to Bosch, I would recommend changing them all.


I sent all 4 to be cleaned/tested, Unfortunately 1 out of the 4 wasn't able to be salvaged. Which I believe was the problematic one to begin with. I'm hoping to find a replacement injector I can pop into slot 1 until I can source a good OEM one to get rebuilt. My Van has been down for a few months due to a bunch of other repairs, so this is the only set back at the moment. Thanks again Tim, I appreciate all the help!

timsrv
09-24-2019, 04:19 AM
There's 1 on eBay for $55 + another $8 in shipping: https://www.ebay.com/i/331783985624?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=331783985624&targetid=475515276661&device=c&mktype=pla&googleloc=9033612&poi=9026173&campaignid=6469750774&mkgroupid=85991902548&rlsatarget=pla-475515276661&abcId=1141186&merchantid=110240799&gclid=Cj0KCQjw_absBRD1ARIsAO4_D3sb8CxmCrZuO-mxaIIPcKC8TVaCwB-5v6-fXxLsMEx3FEZWikeKChwaAnFwEALw_wcB

Better snatch it up quick as it's his last one. Tim

Carbonized
09-24-2019, 10:17 AM
Is the place of origin china? That doesn't look like Japanese characters to me?

Carbonized
09-24-2019, 10:32 AM
Scrolled down the detail page: Country of manufacture: unknown.
Shipped from Taiwan.
I smell gas somewhere. Tim?

timsrv
09-24-2019, 11:47 AM
It does have the OE Toyota number in the title and the listing states "NEW OE/GENUINE ITEM WITHOUT GENUINE/OE ORIGINAL PACKAGE" but I agree, it does look fishy. I don't recall ever seeing these made with blue plastic uppers before, but does that mean it's a fake??? Then there's the whole eBay thing.......I've been ripped off and have been sold counterfeit (junk) items off there before. I guess it's worth saying "buyer beware, proceed at own risk" :cnfsd: :?: Tim

Carbonized
09-24-2019, 12:19 PM
The blue color is what gave me the EBGBs. The Chinese are well known for no being embarrassed by such detail, or a missing letter in a name or some small change in a Logo and still claim OE branding. Shouldn't there be an M after the OE?

I have too been tricked by the big 3's that is why I have nickname for them Fleabay, Crooklist, and Crapazone :LOL2:

VanCo
09-24-2019, 01:53 PM
Check out www.lceperformance.com

They don't advertise for Van specific stuff, but they have correct CC drop in injectors. I ran a set of their matched 22RE injectors (same CC as the Van) for several years. You'll want to research the correct CC and plug and call them. They have great customer service.

I'm currently running Bosch 4 hole high impedance injectors from an eBay company called osidetiger. I ran them using the stock computer, now I have standalone injection. You can run the high impedance on the stock computer by deleting the injector resister.

Keeping these vans running means finding creative solutions. Sometimes you get lucky and end up upgrading at the same time.

barlescharkley
09-24-2019, 05:12 PM
I'm currently running Bosch 4 hole high impedance injectors from an eBay company called osidetiger. I ran them using the stock computer, now I have standalone injection. You can run the high impedance on the stock computer by deleting the injector resister.


I have these injectors also, I haven't done anything to the computer and van seems to run fine, I didn't know that these injectors increase cc. How do I delete the resistor?

VanCo
09-24-2019, 05:50 PM
I have these injectors also, I haven't done anything to the computer and van seems to run fine, I didn't know that these injectors increase cc. How do I delete the resistor?

There are many different cc flow rates of injectors that fit the van fuel rail and electrical plug. The flow rate depends on which injectors you bought. I bought larger 330cc injectors because I added a turbo. I believe the stock van is around195cc.

There is a resister pack for the injectors near the airbox. A delete plug came with my injectors. You unplug the resister, and plug in the delete plug. You only want to do this with high impedance injectors. If you delete the resister with low impedance injectors you will fry the injector drivers in the ECU. All the resister delete does is removes the resister from the circuit. If you leave it in with high impedance injectors, the injectors will not get the appropriate voltage and current. It may run, but it's not right.

Jdelgado
09-25-2019, 10:43 AM
I found an injector! (Part# AUS-MP-50186) Should arrive sometime this week.
Never used this brand before but at this point I'll take a chance on it haha. If it ends up not working out, I'll drop in the Bosch injectors and rewire the harness. Thanks again for the input! :)

timsrv
09-25-2019, 02:44 PM
That's awesome! They could probably sell more if they referenced the Toyota part number (would reel in more searchers). Glad you found it! As far as I can tell it looks like a direct interchange. In case anyone else needs one, here's a link to this on Amazon: https://www.amazon.com/AUS-Injection-MP-50186-Remanufactured-Injector/dp/B001AG70PQ/ref=au_as_r?_encoding=UTF8&Make=Toyota%7C76&Model=Van%7C942&Year=1989%7C1989&ie=UTF8&n=15684181&newVehicle=1&s=automotive&vehicleId=4&vehicleType=automotive

Jdelgado
10-04-2019, 10:28 PM
Check out www.lceperformance.com (http://www.lceperformance.com)

They don't advertise for Van specific stuff, but they have correct CC drop in injectors. I ran a set of their matched 22RE injectors (same CC as the Van) for several years. You'll want to research the correct CC and plug and call them. They have great customer service.

I'm currently running Bosch 4 hole high impedance injectors from an eBay company called osidetiger. I ran them using the stock computer, now I have standalone injection. You can run the high impedance on the stock computer by deleting the injector resister.

Keeping these vans running means finding creative solutions. Sometimes you get lucky and end up upgrading at the same time.

are these the ones you're talking about?
https://www.ebay.com/itm/1984-87-Toyota-Van-LE-Fuel-Injectors-2-2L-Best-Upgrade-Available-4-Hole-Spray/202676519931?epid=3007661368&hash=item2f307643fb:g:2SIAAOSwy4hUUbC2

VanCo
10-05-2019, 08:31 AM
are these the ones you're talking about?
https://www.ebay.com/itm/1984-87-Toyota-Van-LE-Fuel-Injectors-2-2L-Best-Upgrade-Available-4-Hole-Spray/202676519931?epid=3007661368&hash=item2f307643fb:g:2SIAAOSwy4hUUbC2

Yeah, that is the seller and style of injector I'm currently running. I'm not running those van specific injectors though, because I need a higher flow rate.

I really like the injectors, I have about 10k miles on mine. They seem smoother, but all I have is my buttscilloscope to gauge it.

They come with the resister delete plug, and new harness pigtails if you need them. One thing I noticed is that they are a bit louder than stock. You get a pretty solid click when they open and close, but I like that, it means they're working.

Jdelgado
10-09-2019, 11:01 AM
Yeah, that is the seller and style of injector I'm currently running. I'm not running those van specific injectors though, because I need a higher flow rate.

I really like the injectors, I have about 10k miles on mine. They seem smoother, but all I have is my buttscilloscope to gauge it.

They come with the resister delete plug, and new harness pigtails if you need them. One thing I noticed is that they are a bit louder than stock. You get a pretty solid click when they open and close, but I like that, it means they're working.



I spoke with others who are running them and they really like this company, So I ordered the van ones from that link! Thanks again for your input.

Is the resister delete plug mandatory for these van specific ones?

VanCo
10-09-2019, 12:23 PM
Is the resister delete plug mandatory for these van specific ones?

Yeah, the replacement injectors are high impedance, and the factory injectors are low impedance. To make the low impedance injectors work with the ECU injector drivers they use a resistor. If you do not remove the resistor for the high impedance injectors the injectors will not have the appropriate voltage and current.

The engine may run without removing the resistor, but it is not proper.

Jdelgado
10-09-2019, 01:45 PM
Yeah, the replacement injectors are high impedance, and the factory injectors are low impedance. To make the low impedance injectors work with the ECU injector drivers they use a resistor. If you do not remove the resistor for the high impedance injectors the injectors will not have the appropriate voltage and current.

The engine may run without removing the resistor, but it is not proper.


gotcha! I'll def use the resister delete plug then. Thanks for the speedy response!

VanCo
10-09-2019, 03:43 PM
gotcha! I'll def use the resister delete plug then. Thanks for the speedy response!

No problem.

I noticed that in the description they mention to contact them if you have an 88-89 model. They may have the correct plug injector for your 89.

iq_artwork
07-03-2020, 11:45 PM
Hello everyone, I'm looking to replace my injectors. Are these the right fit for a '84 van?

https://www.ebay.com/itm/1984-87-Toyota-Van-LE-Fuel-Injectors-2-2L-Best-Upgrade-Available-4-Hole-Spray-/202676519931?_trksid=p2349526.m4383.l10137.c10&nordt=true&rt=nc&orig_cvip=true

In the description says it fit for the vans 84-87.


Bosch Masterace Spacecruiser: 1984 1985 1986 1987 Wagon 3YEC 4YEC Tarango

Diy2k
07-09-2020, 11:19 AM
I was wondering about those injectors as well. I’ve inspected my injectors (exterior) and they look almost done.