Search:

Type: Posts; User: Carbonized; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.40 seconds.

  1. Replies
    16
    Views
    9,956

    Re: Daystar KT09100BK coil spring spacer

    Nop! one box , two identical spacers, one axle.
  2. Replies
    32
    Views
    20,020

    Re: Best Lift Kit?

    I think the original rubber pad is more of an insulator than anything else. It prevents the metal to metal "sqwicking and clinking" , and the two parts rubbing themself to bare metal and rusting....
  3. Replies
    198
    Views
    48,868

    Re: Charging Air Conditioning System

    Man, if you have one, never mind two, regular O rings that match the length of those two guys, RUN! don't walk, to the nearest FL Lottery tickets vendor :roflmao:
  4. Replies
    106
    Views
    48,926

    Re: Radiator for 4WD

    Fitting a 4wd rad. in a 2wd van is a mater of brackets fabrication. The 2wd is bigger so if you use a 4wd sized rad. you will loose some cooling efficiency....
  5. Replies
    21
    Views
    5,315

    Re: Lower Control Arm Bushings

    That's weird, I did a search on Fleabay before the Crapazon one and could not come up with a 4WD filter for the van.
  6. Replies
    21
    Views
    5,315

    Re: Lower Control Arm Bushings

    Amazon has a boat load of camber caster bolt kits including Specialty product 25425. I do not have time to verify the fit but there are other Toyota choices as well.
  7. Replies
    21
    Views
    5,315

    Re: Lower Control Arm Bushings

    In this case: New bushing = New bolts,new cam washers,new lock nuts. I have never been able to get the old bolts out without some serious damage ( what with the fight against the sawzaw) . Even if...
  8. Replies
    21
    Views
    5,315

    Re: Lower Control Arm Bushings

    The boots alone are absolute NLA I don't know if they have ever been "A"valable. For the 4WD I would look for the whole ball joint for the lower and the whole arm for the upper from scrap yards, flea...
  9. Replies
    18
    Views
    3,334

    Re: Upper engine disassembly

    Have you tried a Flare or Tube wrench? it's open but grabs the head over 5 sides and 4 corners, minimizing the chances of striping the head.

    EDIT

    My bad, if you had room to slide the flare...
  10. Replies
    18
    Views
    3,334

    Re: Upper engine disassembly

    Careful there with PB Blaster and the heat wrench, make sure you invite Mr Fire Extinguisher to the dance :wnk:
  11. Re: What is more likely to get plugged? a Cat or a muffler?

    The cat!
    I had this experience on my Mini. I was tracking the car, so the cat was getting hyper-heated every week-end, the core finally got loose and turned sideways in the can. The Mini chocked...
  12. Replies
    37
    Views
    19,309

    Re: Is Roy Meyers still making push bars?

    You are making a very important point here. We always look at a project as "time and materials" and most of us forget to consider a cost for "brain cells" before calling it pricey, expensive, etc....
  13. Replies
    37
    Views
    19,309

    Re: Is Roy Meyers still making push bars?

    . If that what it was, it was a very reasonable price for a one time custom job :thmbup: You would barely cover materials for that much over here!
  14. Re: New Photobucket policy is blocking some TVT images

    I did a wickipedia search on photobucket, and boy, it's a wonder how this thing is still in business. Interesting read but be warned: pinch you nose before diving 'cause it stinks. Once owned by News...
  15. Replies
    16
    Views
    9,956

    Re: Daystar KT09100BK coil spring spacer

    MD,
    You can cut them yourself easily out of a sheet of hard rubber from Mc Master-car, MSC, Graindger, or any other supply house. Just make sure you chose a high Durometer Shore A (hardness...
  16. Re: New Photobucket policy is blocking some TVT images

    Dear photobucket Teddy,

    This kind of words soup is what we get when corporate greed overcome the geek brain.
    In your effort to purge your site of all "free" accounts, somebody wrote a wrong...
  17. Re: I am getting ready 2 put 2c in my gas 89 4x4

    Spacecruiser, at a 6100 ft elevation, you may want to reconsider the C and look at the Turbo version of the 2C. Then It gets a bit more complicated.
  18. Replies
    25
    Views
    7,984

    Re: Exterior trim pieces and clips

    I should check again but last year I found a small shop that did 3D printing, but the cad work made it so unaffordable that I gave up on it. Now they have some hand held scanners that should make it...
  19. Replies
    28
    Views
    6,784

    Re: Steering wheel shake, smoking right wheel

    I recently took my wife Civic to the stealership for service, while I was waiting, the tech send me a video of him removing the AC filter zoomed on it and asked me if i would authorize replacement,...
  20. Replies
    28
    Views
    6,784

    Re: Steering wheel shake, smoking right wheel

    How did the old bearings look?
    I hope that does it for you once and for all :thmbup:
  21. Replies
    39
    Views
    15,568

    Re: Power steering using alot of fluid!

    Just make sure you use these. The hedges are rolled and the slots are indents: Nothing there to cut into the rubber if slightly over...
  22. Sticky: Re: The WHAT-IS-THIS-PART and WHAT'S-THE-PART-NUMBER Thread for US Toyota Vans 1984-1

    And please post back to confirm : Worky.. No worky :wnk:
  23. Replies
    28
    Views
    6,784

    Re: Steering wheel shake, smoking right wheel

    If you have smoke at that time try and use your nose to identify the smell. Rubber, brake materials and grease, all have a distinctive smell. (Easy for me to say, I could do that in my sleep) Metal...
  24. Replies
    28
    Views
    6,784

    Re: Steering wheel shake, smoking right wheel

    Bad shock??? = Wheel bouncing like a beach ball, or more like an air plane doing a 1000 landing a minutes = shake and smoke! Doesn't explain the intermittence

    Drive shaft CV Joi.... never mind ,...
  25. Replies
    28
    Views
    6,784

    Re: Steering wheel shake, smoking right wheel

    Shacking: something is out of balance or binding. Smoking: something is overheating from chafing or binding. Not pulling to one side and intermittent : very weird indeed! You're right, it might not...
  26. Replies
    63
    Views
    26,692

    Re: Upgrading to 15" rims

    Actually, designSTUDIO, a negative offset moves the outer lip of the rim outboard, (street side). check post #27 and #28 of this thread. Also there is a small difference between the US van and the...
  27. Re: Urgent need for advice on space van wheels (OEM and alternate rims)

    I don't know AD, 185 is only 10 millimeters narrower than stock but the side wall at 65% is 120 millimeters, versus 146 stock, and you have to stretch that to 7" versus 5.5"... They might mount but...
  28. Replies
    16
    Views
    5,250

    Re: Coolant and Oil Leak

    Can't wait! :thmbup:
  29. Replies
    2
    Views
    2,328

    Re: slider door track/trim removal

    :roflmao::roflmao::roflmao: If only it was that simple :rol:

    There are studs in the back of the track with nuts only accessible from the inside. If your van is a cargo, No biggy! If it's a full...
  30. Replies
    9
    Views
    3,438

    Re: Clutch has nada

    What did you do to make it work? Share Please.:thmbup:
  31. Replies
    17
    Views
    9,338

    Re: The Cooling System Troubleshooting thread

    A little item of fairly high importance omitted, if I may:

    9. Fan shroud: verify that the bottom part of the shroud is there. If not, or not sure go there...
  32. Replies
    90
    Views
    50,772

    Re: Is it the infamous hot soak......

    What if you run the return line through the fuel cooler? You get a cooler tank = no pump cavitation = cooler fuel in the lines and injectors= more power, cleaner burn = less chances of hot soak :)>:...
  33. Replies
    90
    Views
    50,772

    Re: Is it the infamous hot soak......

    I'm still, once in a while, tinkering in my head with the the remote bilge pump idea. So the other day I'm on this Porsche forum, here is this guy trying to cool the AC condenser with one of this:
    ...
  34. Re: Over heating / reservoir full / cold air from vent

    Great :dance2:Hopefully you have an event-less trip. Can you take a minute to confirm after your return? please. And can anybody explain why the full return tank ???? I went to look at a van for sale...
  35. Replies
    39
    Views
    15,568

    Re: Power steering using alot of fluid!

    From the look of it, the clamp has been moved once down the neck of the hose barb fitting. You can see in-prints in the rubber just above the hose clamp. This kind of clamps can mash a rubber hose...
  36. Sticky: Re: The WHAT-IS-THIS-PART and WHAT'S-THE-PART-NUMBER Thread for US Toyota Vans 1984-1

    Load sensing proportioning and by-pass valve (LSP & PV ). It adjust the front to rear brake balance depending on weight and location of the load in the van. :)

    If the van has been lifted ( looking...
  37. Replies
    73
    Views
    36,057

    Re: Replacing Fuel Injector(s)

    The blue color is what gave me the EBGBs. The Chinese are well known for no being embarrassed by such detail, or a missing letter in a name or some small change in a Logo and still claim OE branding....
  38. Replies
    73
    Views
    36,057

    Re: Replacing Fuel Injector(s)

    Scrolled down the detail page: Country of manufacture: unknown.
    Shipped from Taiwan.
    I smell gas somewhere. Tim?
  39. Replies
    73
    Views
    36,057

    Re: Replacing Fuel Injector(s)

    Is the place of origin china? That doesn't look like Japanese characters to me?
  40. Re: 1988 manual 4wd le, central Florida ($4,000)

    Did you get my PM?
  41. Re: What are hard to find parts worth getting at pull yard?

    :whs::LOLabv:
  42. Replies
    22
    Views
    9,702

    Re: Safe spots to raise front end with a jack?

    :whs: can't beat this! :thmbup: #1 be safe.
  43. Replies
    22
    Views
    9,702

    Re: Safe spots to raise front end with a jack?

    Ok looks like he used the sub frame that Vanco described in a earlier post. If so don't worry about damage done to the van, that is about the strongest area of the under side of the van. It is also...
  44. Replies
    22
    Views
    9,702

    Re: Safe spots to raise front end with a jack?

    ".....Also still not sure if the car was already damaged when roadside assistance changed the tire with their hydraulic jack under the front axle....."

    Are you sure he used the driveshaft? It's...
  45. Replies
    22
    Views
    9,702

    Re: Safe spots to raise front end with a jack?

    At the back of the van the axle is one single solid piece across, drive shafts and differential are internal, you would not have any problem jacking up the van from the axle.
    At the front ,the axle...
  46. Replies
    22
    Views
    9,702

    Re: Safe spots to raise front end with a jack?

    There is two “horns” from the main body to the front bumper, anywhere along that , ahead or behind the axle , should do. I def. would avoid loading the drive shaft sideway!
  47. Re: Strange Exhaust Noise - Help with diagnosis please

    The bugger with the bad cat theory is that it's not throwing a code! Anything that has to do with emissions is usually throwing codes left, right, under and over!
  48. Re: Strange Exhaust Noise - Help with diagnosis please

    Yep it get your attention :yes:.
    The thing with Gambit problem is, it doesn't throw a code :cnfsd:. I don't see it on the list of things he has done but I assume he checked the air filter. It...
  49. Re: Strange Exhaust Noise - Help with diagnosis please

    BB, the catalytic converter does not have baffles but is has a honeycomb core that can burn itself loose in the can.(Ask me how I Know) If it melt itself enough it can turn sideways in the "can" and...
  50. Replies
    17
    Views
    9,141

    Re: 4WD rear shocks

    These are replacement parts for the Tacoma. They will fit fine without mod on a lifted Van. It is the front one (Dacota's) that need some adjustment, My bad!
    Google " lift kit ToyataVanTech" there...
Results 1 to 50 of 500
Page 1 of 10 1 2 3 4