Search:

Put the project on hold but I have had springs done before by these guys and I am sure when I get the time they will do a great job. They need the old ones to match so I have to put her on blocks for...

AutoZone has a repair link on their site showing torque specs, pics, and explanations... I couldn't find my Previa shop CDS so was very thankful when replacing the SAD, front wheel bearings,...

If I pull the springs out Pohls springs in spokane can make a set, roughly 225 front , 225 back

The couplings have finally gone bad and causing vibration on my 93 Previa SADS.... 360,000 miles approx with 80,000 on the low mileage motor shipped from Japan. Any new input on the aftermarket...

Has happened in mine, similar to washing car engines off with distributors, you may need to mark your connections/ ignition wires remove as well as pop off distributor cap and check all for moisture,...

Looks like some dealers that are online can be searched and have a few in stock , depends on years for my 93 all trac they run about 110.00 a piece 20 to ship

for the 93 its toyota part 48131 and 48132 So they are different. probably since they sit in R and L sides struts

https://www.toyotapartsdeal.com/oem-toyota-previa-coil-springs.html

I do apologize for just assuming the sites that list them , have them.... what now! Any wrecking yards you can get an example from for your spring maker? Good Luck ! I would assume the left...

When I looked online, with a just a random search there were multiple places selling springs.... at least for 91 - 97 previas.

pohls springs Spokane WA

We have a local spring place that can do anything, better quality, no shipping... call around. I am replacing the suspension in our 93 previa 350,000 miles :)

The first thing I would check, which you may have already, is your radiator... with a digital thermometer to see if it has dead spots....
in my experience rigs with over 100,000 usually have...

Update on motor from Japan,
After two years and now at 325,000 miles still runs like new.... I'll check my numbers but also seem to be getting better mileage then new :)

I rebuilt top-one then was thinking metal on metal is not a good idea ... rolling or not so ordered the whole set delivered from village toyota out of florida.... no tax free ship arrived in a few...

https://www.youtube.com/watch?v=lWmfs07SZAU

you tube link showing the three slider arms off so you can see how they roll. Also shows replacing some worn parts and how using a caliper is needed to...

Just had another blower resistor get cracked and solder point split, even resoldering it did not fix it..... due to the ceramic covering split... . This one was new 4 months ago...... any tips? ...

To access this
1.I removed the air intake for heating/cooling.... 4 Phillips screws with washers attached , the cowling wraps around the hood latch and exposes the blower fan once removed.
2....

Parts Ordered
1993 Toyota Previa Blower Motor Resistor Price: $40.33 Core: $0.00 Extended Warranty: $0.00 Qty: 1 Part #: W0133-1750730





Sub Total:
$40.33

FYI make sure , if you replace the resistor board behind the motor, you have it installed with a little lock tite. I believe that my OEM and the second one I replaced became compromised due to...

just puller the board out behind the blower motor the ceremic block was cracked and one solder point broken. I resoldered it and now all the blower setting high to low work and electric burnt smell...

I had replaced a bad blower motor last summer when it quit working on low then finally high as well. Also replaced the board that controls the high to low settings behind the motor. It has been fine...

Thanks , replaced air filter and reset codes , so far running well again . I know these can go out in stages so at least now I know to pass on the OEM ones when these ones really fail .






...

I am reading a code 27 sub o2 sensor, they are original at 280,000.
I replaced the motor 2000 miles ago with one from Japan. Ran great, pre engine light,now a little sluggish .
I was thinking of...

found the codes from an old post thanks though
just let me know on the throttle body
donny

Hey Tim
I'll probably never have a use for the throttle body that came on my used motor from Japan, I'd happily send it to you for the help I have gotten from this site.
Donny
93 previa
PS ...

The control cables just feed in from the end not pushed in from top! Sweet and much easier.

Morning,
So I just noticed , when I was testing my new LEDS that the dimmer dial was effecting the fan.
When the motor was running the LEDS seemed not effected by the dimmer dail but the fan...

Now my fan works I'm replacing mine, the blue LED"S are great ! Any tips on reinstalling the control cables .... do they push in from the end or push down from the top? I carefully pried up and off...

Replacing all dash board bulbs ( LED) and heater panel ones as well anyways :)

Found the problem. First everything checked out fine switch , circuit breaker, relays , the problem was there is a connector between the fan and fuse board located behind the cowling above the fan...

Thanks Tim
yes no power at motor wires or at resistor 12 v setting on my fluke ground at battery ,will check connections as you suggest.
Donny

So fan started working sporadically . Replaced relay. And resistor tested at fan, no power. Ac light on and can feel relay click with low speeds, high speed relay clicks at high speed. When jumped...

So fan started working sporadically . Replaced relay. And resistor then tested at fan, no power. Ac light on and can feel relay click with low speeds, high speed relay clicks at high speed. When...

tip to removing screws tucked in , after cup holder removal, a stubby 1/4 drive ratchet with Phillips tip, allows 90 degree access with some pressure

so not thinking its switch it self I meant to say , thanks for wiring diagram .

it does have new resistor and relays not new circuit breaker
..

still not finding why no power to fan or resistor, when its on and ac switch light on hand on relay you can feel it click going from off to low then you feel the next relay click when going to high....

So when i remove the circuit breaker the ac light goes out and using my volt meter I get over 12V same thing with removing relay but I'm just plugging my volt meter in random slots. After putting...

Hey Tim
same problem here, blower only worked on certain speeds, replaced relay and resistor, not circuit breaker. I put 12 volts directly from battery to fan and fan purrs. No power at fan plug...

Thanks!
ill back up the stands with blocks and house jacks for sure. I've got a neighbor with a tranny jack I can use as well. I'm looking forward to turning this baby over once it's in.

Donny

I'm starting my swap out this week, purchased my engine from Matko engines in CA for 700 shipped to my house. It looks barely used, dipstick and oil cap show signs of low mileage and no burn't oil...

Thanks Tim , looks like it lost enough coolant to get overheated..... the valves are shot and head warped, with 260,000 miles I'm looking at a japanese replacement for 700,00. Wish you could put...

When I pulled my head off 93 AWD Previa ( engine not removed) the shim I made to hold the chain and sprocket in place came off and the sprocket with it. Any tips on lining everything up. it's close...

I know I need to repair mine plus the upper and lower slides are probably shot as well, any tips on those upper and lower for bearing size and/or pics would be appreciated!