I have the 2CT repair manual in PDF form here: https://drive.google.com/drive/folders/1Jb29YwYTDo1VrEBuDplm0mFc-XDVyXfQ?usp=sharing
That should get you started at the very least.
Type: Posts; User: Duke; Keyword(s):
I have the 2CT repair manual in PDF form here: https://drive.google.com/drive/folders/1Jb29YwYTDo1VrEBuDplm0mFc-XDVyXfQ?usp=sharing
That should get you started at the very least.
Just a thought to simplify your setup. I do a lot of traveling in my van and like you wanted a way to charge my laptop. I purchased one of these...
I used the WPT004 when I did the timing belt/water pump on my '88 Master Ace. No problems in the last couple of years that it's been in service.
I recently had to replace the lower control arms on my van due to an accident. Everything I read on here stated that they were NLA. I was able to get a pair of NOS ones from Japan through the web...
Not sure about your 2WD petrol van, but my 1988 4WD Masterace definitely had the load sensing valve.
I believe that they are still available from Toyota. I think they were around $30 each last time I checked. Not sure what the P/N is though.
Much better. It tucks up nicely and is barely noticeable when looking from the side. With all the other stuff that hangs down under these vans (gas tank, transfer case, etc) it's the least of my...
As requested, here are some pictures of the exhaust. It is 2.5" stainless steel. I reused the stock flange at the turbo elbow. The muffler is a Magnaflow straight through model that I had laying...
If oil was leaking past the turbo seals there is a good change the turbo would still be functioning OK, but when oil pressure builds (when the rpm's go up) oil would be getting pushed past the seals...
Have you checked the turbo? It kinda sounds like a turbo seal to me. You could pull off the intake piping a check for oil residue.
When I first purchased my van it was definitely pretty damn slow. Couple that with the stock "speed chime" and freeway cruising was mildly frustrating. My van serves as my main form of...
Glad I found this thread! Ever since I got my van the two low speed blower settings didn't work. Just installed a new resistor and they work perfectly now! Love it when a fix is easy. Thanks...
I'm interested to hear what you come up with. The power locks for the slider and rear door on my van will unlock, but not lock. I can hear the solenoids trying activate the mechanism, and can even...
The mounting bolts are M12X1.25 IIRC.
Definitely. On my Datsun I have found crazy size variances! On that car I have little to no clearance (literally millimeters) and it has bit me in the ass a couple of times. I have found that...
I have 215-75R15's on my van and I have some minor rubbing issues in the front. It is not bad enough that I have felt the need to trim anything, but it is there, especially with a passenger. The...
I have been having similar issues with mine. Been in pretty cold weather for the last week (lows in the teens at night) and my van starts easily but misses and smokes like a chimney until it gets a...
I second the thanks for the R&D and reporting it back. I have been considering electric fans to help get a bit more power and economy from my diesel van, but I think I will take that off of my to do...
Did this exact job a few months back. I ordered all of the parts from rockauto.com.
Water Pump – Asin WPT004
Timing Belt – Gates T098
Timing Belt Tensioner – Gates T41077
Timing Belt Idler –...
I think tank size is in the 14-15 gallon range. The most I have put in is 13.5 gallons, and I was holding my breath all the way to the gas station.
The best I have gotten is 27mpg (lifted with...
Part number should be 17201-64050. I have done some google searching and found some sources from China, but like I said, I'm worried about quality with these parts. It would be nice to be able to...
When I purchased my van the PO told me that a larger turbo was installed by the importer. Doing some research I figured out that it is a CT20 from a 2.4L Land Cruiser. After installing a boost...
I don't know what the lift was at with the KYB's, maybe 1.5 inches over stock? I would guess I'm at about 2 inches over stock right now. Just high enough to fit 215-75R15's with very minimal...
I installed the Bilsteins a few months back to replace the pretty much brand new KYB's that came with my van. With the KYB's it was obvious that the front was underdamped, and over big bumps the...
I purchased the oil filter listed in this post (Wix 51368) and it didn't fit on my van ('88 Masterace Surf 4wd with a 2C-T). I ended up using a WIX 51515, which fit perfectly and is what I have used...
Does your van have an automatic or manual transmission. I remember reading that only the auto's had EGR. I would be interesting in seeing pictures of what you did if you have any.
Selling a set of 5 General Grabber AT2's in the popular 27X8.5R14 size mounted on stock 4x4 van wheels. These were on my van when I purchased them and the PO said that they were mounted less than...
I'm trying to find a replacement clutch kit for my 1988 Masterace 4wd with a 2CT. I've done some searching and turned up the Toyota P/N's for the individual parts, but they are pretty expensive. I...
Do you still have the passenger side mirror?