Search:

Type: Posts; User: originalkwyjibo; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.11 seconds.

  1. Re: Oil Pressure, Radiator, and Battery/Charge Light all come on at the same time.

    I had a diode burn out in the warning light circuit in the instrument cluster that caused my light to come on several years ago. There's no substitute for thorough troubleshooting. Otherwise you are...
  2. Re: Oil Pressure, Radiator, and Battery/Charge Light all come on at the same time.

    Sounds like classic Christmas dash fellas. Possibly a regulator issue causing an overcharge condition at higher RPMs.
  3. Replies
    28
    Views
    10,990

    Re: Wheel bearing parts

    I will concur that they are lifetime lubed double sealed bearings as I have two axles shafts with newly installed bearings sitting in my garage awaiting installation.
  4. Replies
    4
    Views
    877

    Re: Door chime

    There is a black box under the left side of the dash behind the speaker, unplug it. No more chime:thmbup:
  5. Re: trying to identify rubber bits on sliding windows

    Check out the window rehab blog posted by carbonized. Maybe you could reach out to him for an update.
  6. Replies
    62
    Views
    45,417

    Re: Power Steering Leak

    The large o-ring in the kit goes there. Tim posted a PDF of the pump rebuild from the service manual earlier in this thread that explains how to disassemble and rebuild if you need it.
  7. Replies
    3
    Views
    1,078

    Re: "Pop" noise when making sharp U Turn

    My guess would be the steering stop bolts as mine does the same thing at full lock. There is supposed to be a plastic cap on the bolt heads in the lower balljoint to cushion the contact point on the...
  8. Re: MasterAce 2CT Black Smoke, low acceleration

    Rings aren't the only reason for bad compression. It could be a bad valve or camshaft or even a leaky injector among other things. It may be worth doing a little more diagnosing before a teardown....
  9. Replies
    25
    Views
    11,458

    Re: Oil Light Problem

    If you just want the oil level light to stay off and are already diligently checking your oil, you can unplug the level sensor where it connects to the alternator harness and put a jumper wire into...
  10. Replies
    3
    Views
    1,171

    Re: Dynamic Weight Capacity - Roof Load

    The roof itself has no real support and should really not have anything mounted to it. It is just the sheet metal skin with two VERY light gauge support bows that are basically only to keep the sheet...
  11. Re: Fresh rebuilt engine swap, idle/timing problems

    Good to hear it's running well.
  12. Re: Fresh rebuilt engine swap, idle/timing problems

    The gauges in these get pretty inconsistent as they age. If I were in your position, I would be inclined to verify opp erating temps with a non-contact infrared thermometer or by installing an...
  13. Re: Fresh rebuilt engine swap, idle/timing problems

    Yes, the green circle is where both of mine have the engine side of the ground cable attached. Be sure your negative battery cable goes from the battery to the chassis and then on to the engine and...
  14. Replies
    6
    Views
    1,832

    Re: Mystery hose

    The hose on mine went from the dipstick tube to a vent port on the top of the transmission case. The picture is taken from just behind the battery box looking across the top of the transmission...
  15. Re: Fresh rebuilt engine swap, idle/timing problems

    The end of the second leg of the battery ground cable does go under a bolt on the engine side of the driver side engine mount. There is also a harness ground strap that should be attached to the...
  16. Replies
    6
    Views
    1,832

    Re: Mystery hose

    If it is a vent, it would not connect to the engine. It's purpose would be to allow the transmission to breath. When the fluid heats up it expands and if the transmission were totally sealed it would...
  17. Replies
    6
    Views
    1,832

    Re: Mystery hose

    I haven't had a chance to look at either of mine but if one end of the hose is attached to the dipstick tube then it's probably a just a vent.
  18. Replies
    26
    Views
    12,435

    Re: Check engine light will not reset

    You won't damage the starter or alternator and as far as the relay test, continuity and ultimately function is more important than resistance. If the starter cranks, the relay is working. 1 and 3...
  19. Replies
    26
    Views
    12,435

    Re: Check engine light will not reset

    I was reading too many threads and got yours mixed up with someone else's that's an auto. The relay seems to be there instead of having a second clutch switch to kill the cruise control when the...
  20. Replies
    26
    Views
    12,435

    Re: Check engine light will not reset

    The wiring schematic I have doesn't show a starter relay for autos. Where is the relay located on yours?
  21. Replies
    9
    Views
    3,919

    Re: Rear end swap

    On a 4WD the ratio of the front and rear differential must match. A small variation of a couple hundredths is acceptable such as 4.09 in one axle and 4.11 in the other. If the ratios don't match than...
  22. Replies
    9
    Views
    3,919

    Re: Rear end swap

    You can't swap the complete rearend because of the different axle bolt pattern. You could swap the center section but 4WD Autos are an odd 4.778 ratio and gearsets are hard to come by. Check the ID...
  23. Replies
    46
    Views
    20,172

    Re: 14" tires for 4WD (stock rims)

    I have no experience with that brand. Do your due diligence. None of the reviews on that site really pertain to actual experience with the tire so not much help there.
  24. Replies
    46
    Views
    20,172

    Re: 14" tires for 4WD (stock rims)

    Hey Tim.
    My brother has had a set of the Nankang's on his VW Westfalia for a few years and is happy with them. I actually told him about them based on your recommendations. I prefer a more...
  25. Replies
    46
    Views
    20,172

    Re: 14" tires for 4WD (stock rims)

    The first tires I had were the BFG's. Despite being the same size they had the narrowest tread width. Tire width can be measured at the tread or at the sidewall below the tread when mounted to a...
  26. Replies
    46
    Views
    20,172

    Re: 14" tires for 4WD (stock rims)

    I personally much prefer the handling and performance of a LT series "C" rated tire. I have run in an LT27X8.50R14 size the now discontinued BFGoodrich All-Terrain t/a KO and Wildcat A/T's as well as...
  27. Replies
    6
    Views
    1,751

    Re: Is front body panel removable?

    I had someone at an emissions test station who was having trouble picking up a tach signal outside the vehicle ask me to pop the hood so they could hook up directly to my engine. This was said to me...
  28. Replies
    6
    Views
    1,751

    Re: Is front body panel removable?

    I would ask, "How badly do you want to remove it?". If you are simply hoping for easier access to components behind the dash you are unfortunately out of luck. On the other hand, if a badly damaged...
  29. Replies
    12
    Views
    2,860

    Re: Bad Coolant Leak + Overheating

    Try one of these.
    https://www.amazon.com/OTC-4521-Hose-Removal-Tool/dp/B0050SFZBG
    Or Google "radiator hose removal tool". They come in different shapes, lengths, and angles.
  30. Replies
    12
    Views
    2,860

    Re: Bad Coolant Leak + Overheating

    These are invaluable for coolant leaks.
  31. Re: 1987 Van 5 speed manual wonít go into gear.

    I believe so. They are the smaller diameter ones that Burntboot was referencing.
  32. Re: 1987 Van 5 speed manual wonít go into gear.

    Nevermind. That came out unbelievably fuzzy.
    Page MT-36.
    Transmission mounting bolts 53 ft lbs
    Stiffener plate bolts 27 ft lbs.
  33. Re: 1987 Van 5 speed manual wonít go into gear.

    Here you go. All right there in the manual.
  34. Re: 1987 Van 5 speed manual wonít go into gear.

    Also helps to prevent broken fasteners.
    Like Burntboot said, we were all noobs once and I broke plenty of fasteners before I learned to use my torque wrench more often. Experience eventually gave...
  35. Re: '86 Van LE 4Y-EC Engine Severe Valve "Lash" Non Adjustable Valves

    https://www.toyotavantech.com/forum/showthread.php?3724-Refreshing-the-engine-(rebuild-and-aftermath)
    It's a long read but with a lot of relevance to your situation.
    BTW, I searched "lifters".
  36. Replies
    6
    Views
    1,766

    Re: Oil + Filter Change (How-to)

    I would add that it is helpful to punch a hole in the top of the filter before pulling the drain plug to allow the filter to more readily drain back to the pan. This has saved me a considerable...
  37. Replies
    27
    Views
    4,756

    Re: front blower mystery-resistor bypass?

    There are three resistors on the resistor pack each of a different resistance value, one for each of the three lower fan speeds. There is one terminal connected to each of the three low speed outputs...
  38. Replies
    27
    Views
    4,756

    Re: front blower mystery-resistor bypass?

    This would be a good start. You may find the original wiring in the process.You could also test for voltage at the resistor itself. Unfortunately, figuring out and fixing other people's "repairs" is...
  39. Replies
    5
    Views
    1,512

    Re: 1986 with 4YE Wont run

    Sounds like your next check should be to verify fuel to the cylinders. You may have fuel to the rail and the injectors but it may not be getting through the injectors to the cylinders. Sparks plugs...
  40. Re: 1995 Previa has fuel & Spark but won't stay running

    Is your 95 OBD1 or 2?
  41. Replies
    5
    Views
    1,512

    Re: 1986 with 4YE Wont run

    Have you checked codes? Also, these need a fuel pump capable of around 40psi. They are also controlled by an electrical circuit tied to the computer, the airflow meter, and several relays. My...
  42. Re: 1995 Previa has fuel & Spark but won't stay running

    Have you checked for codes?
  43. Re: MasterAce 2CT Turns over but won't start

    Hard to tell from the video but it sounds like injector nailing. This can be caused by the injectir popping too soon which affects the timing as well as allowing too large of fuel droplets. This may...
  44. Replies
    4
    Views
    1,375

    Re: Engine rebuilder/jdm engine help

    Bud's Machine Shop in Lakewood for a rebuild. Not van specific, but a damn good machine shop. Just don't tell them you're not in a hurry.....
  45. Replies
    5
    Views
    2,565

    Re: Illumination Issue - Same Circuit?

    In regards to this and your other thread regarding warning lights: In the past I have attempted to convert two vehicles to full led lighting in the instrument panel, ie illumination and warning...
  46. Replies
    5
    Views
    1,573

    Re: Puddled my van

    When I was a teenager, I was wearing shorts(As I always am)standing next to a car near the muffler when this happened. Singed the hair off of my ankles.
  47. Replies
    5
    Views
    1,573

    Re: Puddled my van

    And yes, you should have pulled the plugs and cranked it to pump any water out of the cylinders through the spark plug holes.
  48. Replies
    5
    Views
    1,573

    Re: Puddled my van

    I know that bridge! I was just there on Father's Day.
    I did the same thing to one of my vans when I misjudged the depth of a flooded street in downtown Tacoma several years ago. Unfortunately, the...
  49. Replies
    1
    Views
    2,082

    Re: Sudden acceleration issue.

    Have you checked for trouble codes?
  50. Re: MasterAce 2CT Turns over but won't start

    Just to be clear, the glowplugs should physically be left in. You just don't want any electrical current going to them. Depending on the system, that could be simply pulling a fuse or unplugging the...
Results 1 to 50 of 500
Page 1 of 10 1 2 3 4