Search:

Type: Posts; User: edmyers; Keyword(s):

Search: Search took 0.04 seconds.

  1. Replies
    6
    Views
    8,260

    Re: Parting out a 94 Altrack previa

    Ment to say drive shafts
  2. Replies
    6
    Views
    8,260

    Re: Parting out a 94 Altrack previa

    Sorry sold everything off the van but still have the front and rear drive axles.
  3. Replies
    6
    Views
    8,260

    Re: Parting out a 94 Altrack previa

    I now have the front drive shaft out. Let me know if your still interested
  4. Replies
    6
    Views
    8,260

    Re: Parting out a 94 Altrack previa

    Yes, its still on the van. haven't been able to get the van inside yet for disassembly when do you need the part?
  5. Replies
    6
    Views
    8,260

    Parting out a 94 Altrack previa

    The van has a blown motor. The doors and roof rails and hood are sold already, I haven't begun disassembly yet. waiting for shop time, I'm in WV not far from innerstate 64
  6. Re: Previa transmission mount bushings

    I suggest taking the mount to a shop that has a hydraulic press, I did mine at a shop and had to use a air hammer with cutter attachment and then pressed them in. The problem i had was not finding...
  7. Re: JDM Engine Swap - 1995 LE SC AWD - Vibration on accelleration

    Pulled my spark plugs a couple of days ago and it looks like i have a fuel injector not firing properly on #2 cylinder could be a source for my engine vibration, so I'm wondering if i should use the...
  8. Re: JDM Engine Swap - 1995 LE SC AWD - Vibration on accelleration

    I did a jdm swap a year ago and just today i addressed some vibration issues, this is what i adjusted and replaced so far.
    Sad couplers , transmission mounts, right side engine mount, there's alot...
  9. Re: Recommendations for removing rear wheel bearing that will not move?

    there might be a plate holding the axle and seal onto the axle housing you must remove the caliper and rotor to find out. toyotaparts has a diagram to use as a reference.
  10. Re: Put a 2 inch lift on a 97 Previa AWD LE. Now it vibrates (a bit). Help.

    i installed a lift on a tundra (6"). i had to install bushings on the front differential that lowered the differential down keeping the front axles at about their orginial angle.
  11. Re: Recommendations for removing rear wheel bearing that will not move?

    iv replaced rear bearings on a chevy where i removed both axles, got a piece of rebar long enough to reach the other side of the axle and hit the bearing from the inside pushing the bearing out.
  12. Replies
    17
    Views
    11,781

    Re: Prepping Used Engine

    good job. i didnt post my install pics. because i worked off a car hoist at a garage. kind of cheating. good install set up for future reference.
  13. Replies
    5
    Views
    6,177

    Re: Was my Previa JDM engine not a JDM?!

    when i received delivery of my 95 jdm i had the same questions but its running good. Just keep an eye on the temp and if you can the oil pressure, and fire it up.
  14. Re: Are these speakers in the dash of my '96 Previa?

    i think they are mid range speakers and you should also locate a wiring diagram. i found a second speaker connection in the dash for a power amp, and didnt hook up the radio up right.
  15. Replies
    2
    Views
    3,813

    Re: Run a Previa without the SAD shaft?

    For about 30 seconds engine will get hot quickly.
Results 1 to 15 of 30