Search:

Type: Posts; User: timsrv; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    99
    Views
    79,901

    Re: The hose of death thread

    Here's a quote from another thread:



    The Gates hose is good too (maybe better), but it's just slightly too big OD to re-use the factory spring clamps. I used to think the spring clamps were...
  2. Replies
    6
    Views
    1,073

    Re: Cannot access a specific thread

    ??? Not sure. If I were more IT savvy I would probably know how to do it with a single setting, but sadly I am not. There are upgrades to the software from time to time, so maybe there was a patch???
  3. Replies
    99
    Views
    79,901

    Re: The hose of death thread

    With the valve cover removed you have enough access to see and replace that hose. It's a bit tight, but possible (no need to split and/or remove the intake manifold). There's a "2nd hose of death"...
  4. Replies
    99
    Views
    79,901

    Re: The hose of death thread

    It can be done from the top if you pull the valve cover 1st.
  5. Thread: Snorkel ?

    by timsrv
    Replies
    29
    Views
    20,144

    Re: Snorkel ?

    I want to see a video that shows nothing but the roof rack and the snorkel moving around a lake with exhaust bubbles following behind. :rol:
  6. Sticky: Re: The WHAT-IS-THIS-PART and WHAT'S-THE-PART-NUMBER Thread for US Toyota Vans 1984-1

    There's a hole on the side of the engine block behind the oil filter. Here's a picture of one mounted:

    https://hosting.photobucket.com/images/a23/timsrv/IMG_4477(1).JPG

    It's your "pressure up"...
  7. Re: Load Sensing Proportioning Valve and Bypass Valve ???

    Toyota has specific part numbers for everything and the van LSP&BV part number does not cross over to anything else (it was made specifically for the van). Many Toyota vehicles have LSP&BV set-ups...
  8. Re: Load Sensing Proportioning Valve and Bypass Valve ???

    Yes, but you would need some sort of standard proportioning valve to limit the rear brakes. Otherwise you would be most likely have rear wheel lock-up and loss of control in a hard braking scenario....
  9. Thread: Engine Porn

    by timsrv
    Replies
    20
    Views
    3,273

    Re: Engine Porn

    It looks physically interchangeable as a unit, but not sure what (if any) internal differences there may be. I know now from experience the heads are the same.....except for maybe missing sensor...
  10. Replies
    43
    Views
    22,819

    Re: G53 [2WD manual] Transmission replacement

    In my world I don't worry too much about things like this until they become a problem. Seals can fail so only replacing the seal was an appropriate 1st step (hopefully the end of the issue). However,...
  11. Replies
    8
    Views
    4,456

    Re: need some help from you professor Tim

    That coupler kit from Toyota should work on both of your shafts.......it just won't work on the original 91 - 93 shafts. FYI, the 91 - 93 shafts went obsolete/unavailable early on so by 2000 or so...
  12. Replies
    43
    Views
    22,819

    Re: G53 [2WD manual] Transmission replacement

    Transmission oil should only be added while the van is level. Once the gear oil is high enough to start dripping out the fill hole, that's the correct oil level. Assuming that part was done...
  13. Replies
    43
    Views
    22,819

    Re: G53 [2WD manual] Transmission replacement

    If you're talking about the Beck-Arnley #052-3382 I mentioned above, that's the one used for automatic transmissions (not compatible with a manual transmission). If you purchased that based on my...
  14. Replies
    6
    Views
    1,073

    Re: Cannot access a specific thread

    Thank you! I just fixed them all. This helps as I don't have a lot of time to scan the forum. It's easy to fix though, so if you find more please let me know. Tim
  15. Replies
    6
    Views
    1,073

    Re: Cannot access a specific thread

    Thanks for pointing that out. I just fixed all those links (including the one in your post above : ). FYI a few years ago our hosting company upgraded our website and added some extra security. When...
  16. Replies
    1
    Views
    566

    Re: Engine Swap Question

    Yes, 3y and 4y engines are interchangeable. The things you mention will not be a problem. The bigger displacement of the 4y will give a noticeable power increase. Even though the intake manifolds are...
  17. Replies
    21
    Views
    31,020

    Re: Automatic 4WD does not 'turn on'???

    Try reading post #5 (this thread). These hubs are very common as Toyota also used them from 1986 - 1995 in the 4wd trucks and 4runners. Just go to eBay and search for "Aisin locking hubs" or similar...
  18. Thread: towing

    by timsrv
    Replies
    28
    Views
    17,513

    Re: towing

    All 4 loops were originally intended as tie-down tabs & like the back they are attached to strong points of the van. They can be used for multiple things and are also good for "recovery" attach...
  19. Sticky: Re: The WHAT-IS-THIS-PART and WHAT'S-THE-PART-NUMBER Thread for US Toyota Vans 1984-1

    That appears to be a left over speaker/siren from an aftermarket alarm system.
  20. Thread: towing

    by timsrv
    Replies
    28
    Views
    17,513

    Re: towing

    The van is a uni-body (no separate frame) so to make the hitch strong I took advantage of everything available. The hooks to which you're referring were used to tie the vans down when they were...
  21. Thread: towing

    by timsrv
    Replies
    28
    Views
    17,513

    Re: towing

    FYI, although there are variables, a heavier tow vehicle will typically be more stable than a light one (you don't want the tail wagging the dog). Of course loading down a light vehicle will cause...
  22. Thread: towing

    by timsrv
    Replies
    28
    Views
    17,513

    Re: towing

    I fabricated a class III hitch for my 87 2wd cargo van today. This van has leaf springs. It's very strong, clears everything, and the spare tire rack still functions normally. Check it out:
    ...
  23. Replies
    28
    Views
    11,899

    Re: Engine Stalls when I hit a puddle in the rain

    I think a banana dance is in order :dance2::dance1::dance1::dance1::dance2: :thmbup:
  24. Replies
    28
    Views
    11,899

    Re: Engine Stalls when I hit a puddle in the rain

    Yeah, these type problems can be very frustrating. I have no problem zoning in on problems when they remain. It's the intermittent ones that I hate.....because they will never be there when you are...
  25. Replies
    28
    Views
    11,899

    Re: Engine Stalls when I hit a puddle in the rain

    Huh? I was going off this information you previously posted:
  26. Replies
    28
    Views
    11,899

    Re: Engine Stalls when I hit a puddle in the rain

    With the key in the "run" position and engine not running, you should see the "check engine" light. If you are not seeing that, then your problem is not the distributor, it's electrical or ECU...
  27. Thread: towing

    by timsrv
    Replies
    28
    Views
    17,513

    Re: towing

    Here's the page from the owner's manual that talks about towing. In a nutshell, they say not to exceed 2,000 lbs.

    11514
  28. Re: A/C, power steering, and fan (water pump/alternator) belts

    The extent of my AC knowledge is pretty much all here in THIS THREAD. It's a long thread (11 pages), but there is some good info and part numbers, so you should take some time to scan/review. On page...
  29. Replies
    29
    Views
    17,438

    Re: Oil Light Problem

    Interesting. Sounds like you may have an intermittent short to ground in your wire harness??? I had a cargo van give me that issue once. I ended up running a new wire from the oil pressure switch up...
  30. Replies
    29
    Views
    17,438

    Re: Oil Light Problem

    Your van has an oil pressure switch (just below the oil filter) and an oil level sensor inside the oil pan. If low pressure or a low level is detected, the same light will come on (2 different ways...
  31. Replies
    29
    Views
    20,477

    Re: Sensors to overdrive

    https://www.ebay.com/itm/362007789161?fits=Make%3AVolvo&hash=item5449587e69:g:iRMAAOSwiONYM3Ab

    Changing to a lower temp T-stat shouldn't have anything to do with your OD troubles, but based on...
  32. Replies
    29
    Views
    20,477

    Re: Sensors to overdrive

    If it engages eventually and your water switch is disconnected, then it sounds like a failing (sticky) solenoid. If that's the case jumping the relay would not help. I had one that was doing that so...
  33. Replies
    109
    Views
    99,356

    Re: Radiator for 4WD

    I thought that looked like WonderWagon's old van. That van started life as an automatic. He did an enormous amount of work on it. Sadly, most of it was before this website and was documented on...
  34. Thread: Engine Porn

    by timsrv
    Replies
    20
    Views
    3,273

    Re: Engine Porn

    The 15" 240SX rims are off the van currently. I will likely get some load range 102 Tires for those rims, but for now I'm using the 14" alloy rims that were used on the Celicas and the original 84 LE...
  35. Thread: Engine Porn

    by timsrv
    Replies
    20
    Views
    3,273

    Re: Engine Porn

    I'm loving it. It just hit 500 miles today since I installed it. It's almost a little spooky because I keep expecting some sort of issue, but there have been zero problems. I got the van at auction ~...
  36. Re: A/C, power steering, and fan (water pump/alternator) belts

    More importantly, what is the pressure rating for that fuel filter, fuel hoses, and the clamps? Normal operating pressure for the van's fuel system is ~ 40 psi and that stuff looks to be only rated...
  37. Thread: Engine Porn

    by timsrv
    Replies
    20
    Views
    3,273

    Re: Engine Porn

    Here are some before and after pics of my cargo van's engine bay. I've put ~ 100 miles on it so far and it runs awesome :thmbup:. I'm going out now to change oil and then going on a job ~ 50 miles...
  38. Thread: Engine Porn

    by timsrv
    Replies
    20
    Views
    3,273

    Re: Engine Porn

    I just got the old engine out, washed the engine bay, then came in for a break. I'm going back out now to drop the new engine in. I'll take some pics. Tim
  39. Thread: Engine Porn

    by timsrv
    Replies
    20
    Views
    3,273

    Re: Engine Porn

    The head was also marketed as a forklift head. I got it from a forklift parts supply business. I'm pretty sure it's a Chinese reproduction. I got the one without valves or any other parts then got...
  40. Thread: Engine Porn

    by timsrv
    Replies
    20
    Views
    3,273

    Re: Engine Porn

    Lol, good eye. I was wondering how long it would take for someone to notice. It's for a forklift. Let's just say I know a guy with connections, a guy with an employee discount who asked not to be...
  41. Thread: Engine Porn

    by timsrv
    Replies
    20
    Views
    3,273

    Engine Porn

    I just finished my latest engine build. It's going in my 87 un-cut cargo van. Check it out :):

    https://hosting.photobucket.com/images/a23/timsrv/IMG_4341(1).JPG
    ...
  42. Replies
    28
    Views
    11,632

    Re: Lower Control Arm Bushings

    I'm not saying this is the right way, but I always remove the nuts and cam washers from the back side, then use a cutting torch on the heads and the threads that extend beyond the cross member. Then...
  43. Re: How to replace your ball joints in about 2 hours (2wd)

    Lol, next time I'm sure you'll start out with the bigger BFG (reference the 6th pic in the 1st post of this thread). It's hard to hit it straight on and hard, but once you get the hang of it they...
  44. Re: How to replace your ball joints in about 2 hours (2wd)

    It's best to only remove the big nut. Leave the 4 small bolts installed (to help with stability), then use the correct size pickle fork and a BFG (Big F______ Hammer). Once the tapered shaft is...
  45. Replies
    28
    Views
    11,632

    Re: Lower Control Arm Bushings

    Yes, it could be done, but so far I've always been able to find them....albeit usually special order. I always keep 4 or more on hand as these tend to freeze up inside the control arm bushings (due...
  46. Replies
    28
    Views
    11,632

    Re: Lower Control Arm Bushings

    Yes, I did. Toyotapartsdeal.com has been becoming increasingly lame. Toyota may be getting low on a bunch of stuff, but I've had several orders cancelled by them (stating NLA), then I was able to...
  47. Replies
    37
    Views
    27,583

    Re: Water Pump Replacement

    You can download the entire 1987 Van Factory Service Manual for free HERE . There were lots of changes between 84 and 87, but for things like the water pump it should be sufficient. If I had an 84, I...
  48. Replies
    43
    Views
    22,819

    Re: G53 [2WD manual] Transmission replacement

    Output seals are easy. After the drive shaft is removed the seal can be pulled. The transmission output shaft is there (slightly in the way) but the seal can still be removed. I use a special seal...
  49. Replies
    34
    Views
    30,979

    Re: Installing a New Brake Master Cylinder

    Replacing the master cylinder isn't bad. It's a little tight but you get enough access just by pulling the cluster. Save the pressure lines for last, fill the reservoir, then use a Mityvac to suck...
  50. Replies
    34
    Views
    30,979

    Re: Installing a New Brake Master Cylinder

    When it comes to a lot of things I insist on genuine Toyota. However, some parts are so simple/basic I don't think it matters. For me, master cylinders, calipers, wheel cylinders fall into that...
Results 1 to 50 of 500
Page 1 of 10 1 2 3 4