Page 2 of 2 FirstFirst 12
Results 21 to 31 of 31

Thread: Lower Control Arm Bushings

  1. #21
    Van Fan
    My Van(s):
    86 2wd auto LE 87 4wd 5spd
    Join Date
    Sep 2017
    Location
    East Tennesee
    Posts
    83
    Rep Power
    1

    Re: Lower Control Arm Bushings

    But ebay shows them from febast....

  2. #22
    Van Obsessed Carbonized's Avatar
    My Van(s):
    87 LE in full "restormodif" mode... ... All Toyota with a twist or two! 89 4WD cargo in need of a little reshaping.
    Join Date
    Apr 2015
    Location
    wherethevanisrare. FL
    Posts
    611
    Rep Power
    1

    Re: Lower Control Arm Bushings

    That's weird, I did a search on Fleabay before the Crapazon one and could not come up with a 4WD filter for the van.
    LG.
    "perfection is achieved, not when there is nothing more to add, but when there is nothing left to take away." A. de St Exupery.

  3. #23
    Forum Newbie
    My Van(s):
    1989 MasterAce Surf Grand Saloon 2CT Auto 4x4
    Join Date
    May 2017
    Location
    Glendale, CA
    Posts
    23
    Rep Power
    1

    Re: Lower Control Arm Bushings

    Did anyone find a camber bolt set that fits the 4WD? I put in an order with ToyotaPartsDeal, but I expect they will shortly tell me they're sold out.

  4. #24
    Administrator timsrv's Avatar
    My Van(s):
    Lots of them
    Join Date
    Jun 2010
    Location
    SW WA ST
    Posts
    6,258
    Rep Power
    10

    Re: Lower Control Arm Bushings

    Yes, I did. Toyotapartsdeal.com has been becoming increasingly lame. Toyota may be getting low on a bunch of stuff, but I've had several orders cancelled by them (stating NLA), then I was able to successfully order through my local Toyota dealer. These camber bolts are one of those things. Febest also makes a replacement. I don't have time to look these up right at the moment, but I'll try to remember to do it later. I'm sure if you search eBay using the Toyota number they will show-up. Tim

    PS: BTW, 2wd vans and 4wd vans use the same camber bolts.......the 4wd has 4 of them and the 2wd only has 2.

  5. #25
    Forum Newbie
    My Van(s):
    1989 MasterAce Surf Grand Saloon 2CT Auto 4x4
    Join Date
    May 2017
    Location
    Glendale, CA
    Posts
    23
    Rep Power
    1

    Re: Lower Control Arm Bushings

    Thanks Tim! Yes it looks like there are some Febest options on ebay. ...aaand I've already had to cancel my ToyotaPartsDeal order.

    Now I'm no automotive engineer, but it does look like the camber bolt assembly on the vans is just... a bolt and some plates. If these Febests weren't available, couldn't a brand new assembly be machined pretty easily? (given the stock was strong enough.)

  6. #26
    Administrator timsrv's Avatar
    My Van(s):
    Lots of them
    Join Date
    Jun 2010
    Location
    SW WA ST
    Posts
    6,258
    Rep Power
    10

    Re: Lower Control Arm Bushings

    Yes, it could be done, but so far I've always been able to find them....albeit usually special order. I always keep 4 or more on hand as these tend to freeze up inside the control arm bushings (due to rust). When I replace them I cake with anti-seize compound to help prevent that. Tim

  7. #27
    Forum Newbie
    My Van(s):
    1989 MasterAce Surf Grand Saloon 2CT Auto 4x4
    Join Date
    May 2017
    Location
    Glendale, CA
    Posts
    23
    Rep Power
    1

    Re: Lower Control Arm Bushings

    Alrighty, I got new cam bolts, I got new bushings, I got new ball joints, but I've also got some very seized old cam bolts on the lower control arms.

    I think I'll have to sawzall the old ones out.

    The cut points on the front cam bolt and bushing are fairly accessible, but does anyone have any special sauce on cutting the back cam bolt and bushing? Should I just drop the rear crossmember out of the way and cut them off from below?

  8. #28
    Administrator timsrv's Avatar
    My Van(s):
    Lots of them
    Join Date
    Jun 2010
    Location
    SW WA ST
    Posts
    6,258
    Rep Power
    10

    Re: Lower Control Arm Bushings

    I'm not saying this is the right way, but I always remove the nuts and cam washers from the back side, then use a cutting torch on the heads and the threads that extend beyond the cross member. Then I use a pry bar to spread the cross-member enough for the control arms to fall out. Sometimes a helper with an extra pry bar and some well placed blows with a hammer can speed things up a bit. If I'm re-using the control arms I'll do the rest of the work with a press. Tim

  9. #29
    Van Enthusiast
    My Van(s):
    Vandi -'93 LiteAce 2CT, Auto, 4wd, Skylite!
    Join Date
    Jan 2017
    Location
    Tulsa
    Posts
    212
    Rep Power
    1

    Re: Lower Control Arm Bushings

    grinder with a 4" abrasive blade, 1/16" can be pretty precise.
    I was a member for 2 years before I bought my van.
    Vandi-

  10. #30
    Forum Newbie
    My Van(s):
    1987 4x4
    Join Date
    Apr 2023
    Location
    Coastside, CA
    Posts
    12
    Rep Power
    1

    Question Re: Lower Control Arm Bushings

    My 87 4x4 seems to be showing signs of needing her bushings replaced. From what I’m reading on this forum and elsewhere, it’s not going to be easy to find the parts I’ll need. Because I’m new to auto repair, can someone tell me exactly what part I would need to ask for? Like, is there a part number or specific size I should ask for as I begin my quest?
    Thanks

  11. #31
    Van Fan
    My Van(s):
    1986 Toyota van
    Join Date
    Sep 2016
    Location
    Tucson,Az
    Posts
    57
    Rep Power
    1

    Re: Lower Control Arm Bushings

    I just looked and they all all available at rock auto the moment. Looks like doorman makes upper control arms now.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •