Page 3 of 3 FirstFirst 123
Results 41 to 51 of 51

Thread: Engine Service Connector not working - can't set proper ignition timing

  1. #41
    Administrator timsrv's Avatar
    My Van(s):
    Lots of them
    Join Date
    Jun 2010
    Location
    SW WA ST
    Posts
    6,202
    Rep Power
    10

    Re: Engine Service Connector not working - can't set proper ignition timing

    It could be a transmission issue then. I'm not a transmission guy, but I'd start out by pulling the pan and replacing the screen/strainer assy. I'd also check for metallic particles in the fluid and on the pan magnets. If the fluid smells burnt and/or there's a lot of metal flakes in the pan, then you may need to visit a transmission specialist.

  2. #42
    Van Fan
    My Van(s):
    Currently: 89 4wd Toyota Van auto 87 4wd Toyota Van 5spd 84 2wd Toyota Van Auto Country Homes Poptop Previous: 89 Mitsubishi Star Wagon (Delica) 87 Toyota Van Le (2wd) 82 VW Vanagon Diesel Camper
    Join Date
    Apr 2015
    Location
    Northeast USA
    Posts
    36
    Rep Power
    1

    Re: Engine Service Connector not working - can't set proper ignition timing

    Okay I'm going to pull the pan and replace the strainer assy. Is it 4WD specific? Is this the right kit? https://www.partsgeek.com/gbproducts...+Kit+1987+1985

    Thanks Tim!

  3. #43
    Administrator timsrv's Avatar
    My Van(s):
    Lots of them
    Join Date
    Jun 2010
    Location
    SW WA ST
    Posts
    6,202
    Rep Power
    10

    Re: Engine Service Connector not working - can't set proper ignition timing

    Yes, that's it. That one fits all years and all models of US vans with auto transmissions. More details on this job can be found in THIS THREAD starting on post #14.

  4. #44
    Van Fan
    My Van(s):
    Currently: 89 4wd Toyota Van auto 87 4wd Toyota Van 5spd 84 2wd Toyota Van Auto Country Homes Poptop Previous: 89 Mitsubishi Star Wagon (Delica) 87 Toyota Van Le (2wd) 82 VW Vanagon Diesel Camper
    Join Date
    Apr 2015
    Location
    Northeast USA
    Posts
    36
    Rep Power
    1

    Re: Engine Service Connector not working - can't set proper ignition timing

    Update, transmission seems to be performing much better after changing the fluid and filter. It shifts more smoothly at the usual RPMs again and engages at lower RPMs in reverse like it used to. The true test will be to see how it performs in the cold.

    Thanks again for your time and help Tim!

  5. #45
    Van Fan
    My Van(s):
    1987 4WD LE
    Join Date
    Jan 2021
    Location
    CA
    Posts
    32
    Rep Power
    1

    Re: Engine Service Connector not working - can't set proper ignition timing

    Quote Originally Posted by timsrv View Post
    With those codes we must be talking about an 88 - 89 van......right? Code 22 is an ECU Temp Sensor code, but if that sensor is bad the van will run REALLY bad, so I'm guessing that's an old code that wasn't cleared. Code #51 is almost always a bad TPS. I would recommend clearing codes, driving the van around for a day or so, then check codes again. If code 51 comes back I'd replace the TPS. Based on my experience with these vans, if the TPS has more than 100k miles on it or if it has an unknown history, I'd probably just go ahead and replace it. Keep in mind there's an adjustment procedure, so familiarize yourself with that before you do the job. I posted a video of how that's done at the end of the 1st post in THIS THREAD. Tim
    Hi Tim,

    I have 212k on the odo. I did pick up a new TPS and haven’t installed it. It runs ok, shifts ok, has a slow take off from the light (maybe just a typical characteristic). What I am unsure of is if I replace the TPS do I need to see the timing again? I had it smogged and they had to set the timing as it was advanced for some reason. I’d hate to compromise any issues when I need to smog it again.

  6. #46
    Administrator timsrv's Avatar
    My Van(s):
    Lots of them
    Join Date
    Jun 2010
    Location
    SW WA ST
    Posts
    6,202
    Rep Power
    10

    Re: Engine Service Connector not working - can't set proper ignition timing

    Replacing the TPS will not affect your base timing, but it can affect your advance. The TPS is an integral part of the electronic advanced system. If the TPS isn't functioning correctly it can disable the electronic advance. To test for this put a jumper wire in your "Check Engine Connector" and verify your timing is set for 12° BTDC, then remove the jumper and check again. If the electronic advance is working you should see the timing jump to ~ 20°. If it's not doing that, and you're getting a code 51, replace the TPS, adjust it per specs given, then check timing again with/without the jumper wire installed. Be sure to clear all codes and drive it for a day or so, then check codes again to be sure none come back. Tim

    PS: I'd also recommend checking the condition of your EGR modulator. If the plastic shows signs of overheating, then it's likely your cat converter is plugged up. Tim

  7. #47
    Administrator timsrv's Avatar
    My Van(s):
    Lots of them
    Join Date
    Jun 2010
    Location
    SW WA ST
    Posts
    6,202
    Rep Power
    10

    Re: Engine Service Connector not working - can't set proper ignition timing

    If it's hesitating/stumbling during acceleration, you should also check the rubber intake boot that goes between the throttle body and the Air Flow Meter. Check for tears between the ribs. Another way to check is to squeeze it while the van is idling. If the van stumbles and/or stalls when you squeeze, then it's almost certainly cracked and it's causing the acceleration problem. Tim

  8. #48
    Van Fan
    My Van(s):
    1987 4WD LE
    Join Date
    Jan 2021
    Location
    CA
    Posts
    32
    Rep Power
    1

    Re: Engine Service Connector not working - can't set proper ignition timing

    Thanks, Tim. Just did a through check, intake boot looks good, no cracks or tears and is pliable.

    If I replace the TPS with a new one, and calibrate it per your video instructions, should I expect a change in timing? If not, them perhaps that will yield the anxiety when I get it smogged. I don't have a timing light, and I remember when I failed smog they said my timing was off and they set it and had to change the cat. They suspected the TPS, but they didn't change it as the emissions out of the tail pipe were good after the repair and there was no check engine indicator on the dash.

  9. #49
    Van Enthusiast
    My Van(s):
    "Hansel" The 1988 5 speed 4x4
    Join Date
    Jan 2015
    Location
    Ojai
    Posts
    222
    Rep Power
    1

    Re: Engine Service Connector not working - can't set proper ignition timing

    hey Socal87, I just replaced the tps on an 1988 5spd 4x4. Initially when I changed the tps, I did not know that the TPS needed to be set position per Tim’s video. I continued to set the timing to 12 btdc. But when I removed the jumper, the timing did not jump to 20 btdc. It was also throwing code 5-1.

    I later discovered the TPS thread trying to trouble shoot why the electronic advance was not working. I went back and removed the TPS and set it per Tim’s video and reinstalled. This fixed the problem, and now the the timing advances to 20 Btdc. From my experience it will not change your base timing.

    However, in order to do this you will need a multimeter that can check continuity, a .028” feeler gauge (or stacked feeler gauges that equal .028) and a Throttle body gasket (or make a gasket from gasket paper as they are no longer available).

  10. #50
    Van Fan
    My Van(s):
    1987 4WD LE
    Join Date
    Jan 2021
    Location
    CA
    Posts
    32
    Rep Power
    1

    Re: Engine Service Connector not working - can't set proper ignition timing

    Hey, thanks for that.. it really helps! I think I might give it a shot. I experienced the same and so did the smog repair shop-- when they jumpered it, it did not have any effect and did not advance. I have to get some feeler gauges and a gasket and playback Tim's video.

    I pulled the codes on it (it's for an 87 4WD LE) and I got a Code 4, 6, and 11. 4 is related to the water temp sensor signal. I changed it out, but might still be bad. Not sure what 6 is related to and that one's new. I did wire up a starter solenoid bypass, so I'm not sure if that's related, but it worked- starts up no problem. And I got the 11 code, which I think is the TPS.

  11. #51
    Administrator timsrv's Avatar
    My Van(s):
    Lots of them
    Join Date
    Jun 2010
    Location
    SW WA ST
    Posts
    6,202
    Rep Power
    10

    Re: Engine Service Connector not working - can't set proper ignition timing

    Yes, on an 87 code 11 is most likely the TPS. Keep in mind the electronic advance changes timing when enabled, but not the base timing. In order for it to run correctly, the base timing needs to be set 1st, then you verify the electronic advance is working by removing the jumper and verifying the timing jumps to ~ 20°. If your base timing is correct, but your electronic advance is not working, it will most likely fail emissions. However, it may be possible to change the base timing to make it pass emissions, but that would most likely create a bigger problem with drivability. If you're a hands-on guy, you need a timing light (nothing fancy, just a basic model). If you're going to use a shop, make sure they know what they are doing and they understand the old-school tech of distributor adjusted base timing with TPS controlled electronic advance. Tim

    PS: If it's running but you have a code 6 stored, that tells me you have old codes stored and you need to clear them. FYI, codes don't go away when you rectify the problem, they only go away when you clear them. Clear the codes then see which ones come back, it's the only way to know you've still got a problem. THIS ARTICLE gives info on reading and clearing codes. Tim

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •